Fixed cycle (Boring 1)

Q: What does Mazak G-code G75 do?

G75 — Fixed cycle (Boring 1) on the MAZATROL SmoothX control (INTEGREX e-670H). (Direction determined by bits 3 & 4 of I14) k : Distance from point Z X, Y, P, Q, D, J(B), K, and/or I can be omitted. Whether argument J or B is to be used depends on the value that has been set in bit 1 of Parameter F84 bit 1 = 1: Argument J-command J-command), setting a B-command will cause the table to rotate. Be careful in that case to ensure no interference between the workpiece and the tool. (Direction determined by bits 3 & 4 of I14) (b ) Value except 0 ····· M04 after machining X, Y, P, Q, D, and/or J(B) can be omitted. Whether argument J or B is to be used depends on the value that has been set in bit 1 of Parameter F84 bit 1 = 1: Argument J-command (argument J-command), setting a B-command will cause the table to rotate. Be care- ful in that case to ensure no interference between the workpiece and

Q: What is the programming format of G75?

G75 [Xx Yy] Rr Zz [Pt Qq ] Ff [Dd Jj (Bb ) Kk Ii ]

Machine-specific. This G-code reference is specific to the Mazak INTEGREX e-670H / e-670H-S with the MAZATROL SmoothX control (EIA/ISO programming manual H747PB0030E). G-code availability depends on fitted options, and groups and behaviour differ between Mazak models and control generations — verify against the manual for your own machine before programming with any code.

What it does

(Direction determined by bits 3 & 4 of I14) k : Distance from point Z X, Y, P, Q, D, J(B), K, and/or I can be omitted. Whether argument J or B is to be used depends on the value that has been set in bit 1 of Parameter F84 bit 1 = 1: Argument J-command J-command), setting a B-command will cause the table to rotate. Be careful in that case to ensure no interference between the workpiece and the tool. (Direction determined by bits 3 & 4 of I14) (b ) Value except 0 ····· M04 after machining X, Y, P, Q, D, and/or J(B) can be omitted. Whether argument J or B is to be used depends on the value that has been set in bit 1 of Parameter F84 bit 1 = 1: Argument J-command (argument J-command), setting a B-command will cause the table to rotate. Be care- ful in that case to ensure no interference between the workpiece and the tool.

G75 is modal (group 09) — it stays in effect until another code of the same group replaces it.

Programming format

G75 [Xx Yy] Rr Zz [Pt Qq ] Ff [Dd Jj (Bb ) Kk Ii ]

Address words

t c : Dwell (in time or No. of revolutions) j 0 : 0 or omitted ········· M03 after machining
q : Amount of relief on the XY-plane (b ) Value except 0 ····· M04 after machining
f 0 : Feed rate i 0 : Distance from point Z
d : Distance from R-point
Note: For a horizontal machining center, if the value of bit 1 of parameter F84 is 1 (argument
t c : Dwell (in time or No. of revolutions) f 1 : Feed rate
q 0 : Amount of relief on the XY-plane j 0 : 0 or omitted ········· M03 after machining
Note: For a horizontal machining center, if the value of bit 1 of parameter F84 is 1

Notes & precautions

For a horizontal machining center, if the value of bit 1 of parameter F84 is 1 (argument

Source

Mazak PROGRAMMING MANUAL for EIA/ISO PROGRAM, manual H747PB0030E, section 13-1-7 G75 [Boring], p. 3-11, 13-10, 13-11. Reference and explanation only — not a reproduction of the manual.

Not sure how to use it? Ask the Mazatrol assistant →