What does Mazak parameter D92 do?

D92 is a User parameter in the POINT group of the MAZATROL SmoothX control (INTEGREX e-670H). 8 bit settings.

Which bits does Mazak parameter D92 have?

Bit 0: During a true-circle processing (end milling) cycle, E17 is used for axial feed or not. Bit 1: The R1-point height of the back spot facing is set to D1 or not. Bit 2: If a chamfering cutter is included in the premachining tool sequence of the same unit, the R-point height of the reamer is set to D1 or not. Bit 3: If a chamfering cutter is included in the pre-machining tool sequence of the same unit, the R-point height of the tapping is set to D1 or not. Bit 4: The position cleared radially or axially by D17 from the workpiece section concerned is subjected/not subjected to check for interference Bit 5: Dwell time designation for synchronous tapping in a MAZATROL program valid/invalid Bit 6: During planetary tapping, chips are ejected/not ejected automatically prior to the threading process. Bit 7: Whether or not to generate alarm 650 CHAMFERING IMPOSSIBLE if idle cutting takes place during chamfering in point-machining unit

‹ALARMSMazatrol Assistant

PARAMUser parameter · POINT (D)

D92

POINT bit settings (8 bits)

Machine-specific. This parameter list is specific to the Mazak INTEGREX e-670H / e-670H-S with the MAZATROL SmoothX control (manual HA64HA0035E). Other Mazak models and control generations use different addresses, ranges and meanings — verify on your own control before changing anything.

Bit settings — D92 is set bit by bit

bit 0
During a true-circle processing (end milling) cycle, E17 is used for axial feed or not.
1: Used 0: Not used
Range 0, 1 · Takes effect: Immediate
bit 1
The R1-point height of the back spot facing is set to D1 or not.
1: Set 0: Not set
Range 0, 1 · Takes effect: Immediate
bit 2
If a chamfering cutter is included in the premachining tool sequence of the same unit, the R-point height of the reamer is set to D1 or not.
1: Set 0: Not set
Range 0, 1 · Takes effect: Immediate
bit 3
If a chamfering cutter is included in the pre-machining tool sequence of the same unit, the R-point height of the tapping is set to D1 or not.
1: Set 0: Not set
Range 0, 1 · Takes effect: Immediate
bit 4
The position cleared radially or axially by D17 from the workpiece section concerned is subjected/not subjected to check for interference
1: Subjected 0: Not subjected
Range 0, 1 · Takes effect: Immediate
bit 5
Dwell time designation for synchronous tapping in a MAZATROL program valid/invalid
1: Valid 0: Invalid Note : Timing of dwell execution of bit 5 is determined by settings in bit 0 to 2 of parameter D91.
Range 0, 1 · Takes effect: Immediate
bit 6
During planetary tapping, chips are ejected/not ejected automatically prior to the threading process.
1: Ejected 0: Not ejected
Range 0, 1 · Takes effect: Immediate
bit 7
Whether or not to generate alarm 650 CHAMFERING IMPOSSIBLE if idle cutting takes place during chamfering in point-machining unit
1: Generate 0: Do not generate
Range 0, 1 · Takes effect: Immediate

Source

Mazak PARAMETER LIST / ALARM LIST / M-CODE LIST, manual HA64HA0035E, p. 21, 22, 123, 124. Reference and explanation only — not a reproduction of the manual.

Not sure what to set? Ask the Mazatrol assistant →