‹ALARMSMazatrol Assistant
PARAMUser parameter · POINT (D)
D96

POINT bit settings (8 bits)

Machine-specific. This parameter list is specific to the Mazak INTEGREX e-670H / e-670H-S with the MAZATROL SmoothX control (manual HA64HA0035E). Other Mazak models and control generations use different addresses, ranges and meanings — verify on your own control before changing anything.
Bit settings — D96 is set bit by bit
  1. bit 0

    Surface speed calculation for spot drill used

    Surface speed calculation for spot drill used 0: Based on machining hole diameter 1: Based on nominal diameter of the tool

    Range 0, 1 · Takes effect: Immediate

  2. bit 1

    Element that determines the counterboring pattern

    Element that determines the counterboring pattern (whether to execute diameter enlarging) 0: Determines the counterboring pattern from the nominal diameter in tool data and the hole diameter in the program. 1: Determines the counterboring pattern from the tool diameter in the tool data and the hole diameter in the program.

    Range 0, 1 · Takes effect: After stop of movement

  3. bit 2

    Setting of the amount of chamfer in the spot drill tool sequence

    The amount of chamfer in the spot drill tool sequence 0: Cannot be specified 1: Can be specified

    Range 0, 1 · Takes effect: Immediate

  4. bit 3

    Menu display setting of RGH BCB (inversed faced hole machining), BK-CBORE (back boring) and CBOR-TAP (counterbore tapping), as well as BACKSPOT FACER (inversed spot-facing tool) and BACK BORING BAR (back boring) in the tool sequence data

    RGH BCB (inversed faced hole machining), BK-CBORE (back boring), and CBOR-TAP (counterbore tapping) are displayed in the menu in the point-machining unit. BACKSPOT FACER (inversed spot-facing tool) and BACK BORING BAR (back boring) are displayed in the tool menu for tool sequence data in the point-machining unit. 0: Invalid (not displayed) 1: Valid (displayed) * Even if the menu display is disabled, the menu is enabled and displayed in the expert mode, i.e. when the SMART mode is canceled.

    Range 0, 1 · Takes effect: At power on

  5. bit 4

    Conditions to determine the CIRC MIL operation for the specification without Y-axis

    Conditions to determine the CIRC MIL operation for the specification without Y-axis 0: Machining in Cycle 1 HOLE- = Tool diameter 1: Machining in Cycle 1 HOLE- ≥ Tool diameter * For RGH CBORE and CBOR TAP, this parameter is valid when D96 bit 1 = 1 and invalid when D96 bit 1 = 0.

    Range 0, 1 · Takes effect: Immediate

  6. bit 5

    Setting of the start point Y of the cylindrical surface in the C-axis point machining unit

    Setting of the start point Y of the cylindrical surface in the C-axis point machining unit 0: Impossible 1: Possible

    Range 0, 1 · Takes effect: Immediate

  7. bit 6

    Smooth chamfering (C-POINT MACH-ING): Switching of the restrictions according to the cutting edge angle of a chamfering tool

    Switching of the restrictions according to the cutting edge angle of a chamfering tool used for Smooth chamfering (C-POINT MACH-ING) 0: Enables machining only when the cutting edge angle is 45. (Alarm if the cutting angle edge is not 45.) 1: Enables machining even when the cutting edge angle is not 45. (Conventional scheme)

    Range 0, 1 · Takes effect: Immediate

  8. bit 7

    Cutting depth in deep-hole tapping/high-speed deep-hole tapping cycle

    Used to select the mode of operation when the cutting depth is not specified or is set to 0 in the deep-hole tapping or high-speed deep-hole tapping cycle. 0: Perform tapping without pecking 1: Alarm

    Range 0, 1 · Takes effect: Immediate

Source

Mazak PARAMETER LIST / ALARM LIST / M-CODE LIST, manual HA64HA0035E, p. 22, 126, 127. Reference and explanation only — not a reproduction of the manual.

Not sure what to set? Ask the Mazatrol assistant →