EIA/ISO bit settings (7 bits)

1. bit 0

   Operation when workpiece counting is made valid while the automatic operation INTELLIGENT SAFETY SHIELD is enabled

   Operation when workpiece counting is made valid while the automatic operation INTELLIGENT SAFETY SHIELD (ISS) is enabled. <Manual setting on the POSITION screen> 0: Workpiece counting is activated while the ISS is disabled, and the automatic operation continues. 1: Workpiece counting is not activated, the alarm 1129 MEMORY PROTECT (SAFETY SHIELD) is displayed and the automatic operation continues. <Setting using programs (#3901, #3902)> (Note 1) (Note 2) 0: Workpiece counting is activated while the ISS is disabled, and the automatic operation continues. 1: Workpiece counting is not activated, the alarm 1824 UNWRITABLE SYSTEM VARIABLE (ISS) is displayed and the automatic operation stops. Note : 1. When parameter F335 bit 7 = 0, operation follows the setting of F143 bit 0 upon overwriting the part count from the program while executing ISS (automatic). 2. When parameter F335 bit 7 = 1, the part count is set upon overwriting the part count from the program while executing ISS (automatic), regardless of the setting of F143 bit 0, and automatic operation continues with ISS enabled. [Related parameters] F335bit7

   Range 0, 1 · Takes effect: Immediate

2. bit 1

   Status of [STORE WORKPCE MATERIAL] when the power is turned on

   Select the status [STORE WORKPCE MATERIAL] when the power is turned on. 0: Disabled (The condition of the material model cut with the ISS enabled is not maintained.) 1: Enabled (The condition of the material model cut with the ISS enabled is maintained.)

   Range 0, 1 · Takes effect: At power on

3. bit 2

   —

   Invalid

4. bit 3

   Setting of the section to cancel the collision check function between the TOOL EYE sensor and the tool with the INTELLIGENT SAFETY SHIELD being selected

   Setting of the section to cancel the collision check function between the TOOL EYE sensor and the tool with the INTELLIGENT SAFETY SHIELD being selected  During manual TOOL EYE measurement 0 : Canceling the collision check function between the TOOL EYE sensor and the tool (cutter, shank) 1 : Canceling the collision check function between the TOOL EYE sensor and the tool (cutter, shank, holder)  During automatic TOOL EYE measurement Canceling the collision check function not only between the TOOL EYE sensor and the tool but entirely.

   Range 0, 1 · Takes effect: Immediate

5. bit 5

   X-axis diameter/radius input mode after the G136 command (measurement macro call)

   X-axis input mode selection after execution of G136 0: According to bit 5 of parameter M18 if G122.1/G123.1 (diameter/radius selection) is not specified 1: Radius values if G122.1/G123.1 is not specified * If this parameter setting is changed after the machine is started, it will become valid after resetting operation. In single-block operation, diameter values are used regardless of this parameter setting.

   Range 0, 1 · Takes effect: Immediate

6. bit 6

   Display of WPC during inclined-surface machining on the POSITION display

   Display of WPC on the POSITION display during inclined-surface machining 0: Display the work coordinate system that is selected before the inclined-surface machining command. 1: Display the coordinate system that is selected after coordinate system rotation and zero point parallel movement according to the inclined-surface machining command.

   Range 0, 1 · Takes effect: Immediate

7. bit 7

   G43 modal cancel selection with the RESET key

   Cancel or hold G43 when the RESET key is pressed in G43 (tool length compensation) mode. 0: Cancel 1: Hold

   Range 0, 1 · Takes effect: Immediate

Mazak PARAMETER LIST / ALARM LIST / M-CODE LIST, manual HA64HA0035E, p. 38, 232, 233. Reference and explanation only — not a reproduction of the manual.