What does Mazak parameter F162 do?

F162 is a User parameter in the EIA/ISO group of the MAZATROL SmoothX control (INTEGREX e-670H). 8 bit settings.

Which bits does Mazak parameter F162 have?

Bit 0: Movement/No movement according to the particular amount of offset during independent start of tool tip point control Bit 1: Type of passage of tool tip point through singular point Bit 2: Chamfer/corner R-command address selection Bit 3: Fixed hole-machining cycle return selection Bit 4: 6 digits in T-command for turning Bit 5: Use of the M Pro scheme as the method of selecting the Length correction axis bit Bit 6: MAZATROL program check for missing Z-offset, valid/invalid Bit 7: Encoder polarity selection

‹ALARMSMazatrol Assistant

PARAMUser parameter · EIA/ISO (F)

F162

EIA/ISO bit settings (8 bits)

Machine-specific. This parameter list is specific to the Mazak INTEGREX e-670H / e-670H-S with the MAZATROL SmoothX control (manual HA64HA0035E). Other Mazak models and control generations use different addresses, ranges and meanings — verify on your own control before changing anything.

Bit settings — F162 is set bit by bit

bit 0
Movement/No movement according to the particular amount of offset during independent start of tool tip point control
During independent start of tool tip point control 0: Movement according to the particular amount of offset 1: No movement according to the particular amount of offset
Range 0, 1 · Takes effect: After stop of movement
bit 1
Type of passage of tool tip point through singular point
0: The same primary rotary axis angle sign as that existing during the start of tool tip point control is selected as the angle of the rotary axis for implementing the tool axial vector specified during tool tip point control. Example : B = positive B = 0 B = positive C = 0 C = 180 1: The angle that provides a smaller amount of rotational movement of the secondary rotary axis on a singular point is selected as the angle of the rotary axis for implementing the tool axial vector specified during tool tip point control. (Both positive and negative signs are available for the primary rotary axis.) Example : B = positive B = 0 B = negative C = 0 C = 0
Range 0, 1 · Takes effect: After stop of movement
bit 2
Chamfer/corner R-command address selection
Chamfer/corner R-command address selection 0 : (I), (K), (R), (,R), (,C), (,A) 1 : (R), (C), (A)
Range 0, 1 · Takes effect: After stop of movement
bit 3
Fixed hole-machining cycle return selection
Fixed hole-machining cycle return selection 0: Initial point 1: R-point
Range 0, 1 · Takes effect: After stop of movemen
bit 4
6 digits in T-command for turning
6 digits in T-command for turning 0: Invalid 1: Valid
Range 0, 1 · Takes effect: After stop of movement
bit 5
Use of the M Pro scheme as the method of selecting the Length correction axis bit
Use of the M Pro scheme as the method of selecting the Length correction axis bit 0: Invalid 1: Valid
Range 0, 1 · Takes effect: After stop of movement
bit 6
MAZATROL program check for missing Z-offset, valid/invalid
MAZATROL program check for missing Z-offset 0: Valid 1: Invalid
Range 0, 1 · Takes effect: After stop of movement
bit 7
Encoder polarity selection
Encoder polarity selection 0: Pulse rate increase for forward rotation command 1: Pulse rate reduction for forward rotation command
Range 0, 1 · Takes effect: After stop of movement

Source

Mazak PARAMETER LIST / ALARM LIST / M-CODE LIST, manual HA64HA0035E, p. 41, 251, 252, 253, 254. Reference and explanation only — not a reproduction of the manual.

Not sure what to set? Ask the Mazatrol assistant →