What is the setting range of Mazak parameter TC62?

0 to 11. A changed value takes effect: Immediate.

PARAMUser parameter · TURNING (TC)

TC62

Selection of tool change command output position for FLASH tool

Q: What does Mazak parameter TC62 do?

TC62 is a User parameter in the TURNING group of the MAZATROL SmoothX control (INTEGREX e-670H). Selection of tool change command output position for FLASH tool INTEGREX e-H [11] 3rd zero point M5 M6 [6] [1] X-axis M5 X-axis [4] Machine [5] [0] 2nd zero point x [7] Dmax Zc z INTEGREX e-V I21/I22 X-axis M5 X-axis [8] [2] I21/I22 Z-axis [4] [9/10] User-specified fixed point 1/2 2nd [7] [0] z [5] Zc Dmax x. When a FLASH tool is used, specify the position for indexing the tool, namely, the tool change command output position for indexing the tool of the same TNo. at the same B-axis angle during programmed operation. In all other cases, the tool change position specified by SU10 becomes valid. I21/I22 Z-axis Zc : Stock material edge projection length Dmax : Stock material maximum outside Z-axis x : Tool turning clearance (X-axis) SU50 [3] + B-axis spindle edge offset value z : Tool turning clearance (Z-axis) SU51 zero point 1 Machine zero point Clearance position 2 Clearance position Machine zero point 3 Machine zero point Machine zero point 4 2nd zero point 2nd zero point 3rd zero point M6 X-axis Machine 7 Clearance position zero point [3] machining M5 point 1 point 1 Z-axis zero point [1] 1. Do not use the setting of TC62 = 4 for the INTEGREX e- series. A collision with the ATC cover is likely to occur since the ATC position specified in fixed-point [6] M5 is present inside the ATC cover. 2. Since x in the case of TC62 = 0, 2, or 5 includes spindle tool length, if the tool is too long (as in the case of a long boring bar), the tool change operation may be software-limited in the +X direction. 3. TC62 = 5 or 6, Z-axis tool change command output position is identical with the end point of previous machining. In the case below, however, this may not As shown here, if the longest tool comes into the hatched portion, the position will escape in Z-axis direction by the distance determined by SU51.

Machine-specific. This parameter list is specific to the Mazak INTEGREX e-670H / e-670H-S with the MAZATROL SmoothX control (manual HA64HA0035E). Other Mazak models and control generations use different addresses, ranges and meanings — verify on your own control before changing anything.

What it does

Selection of tool change command output position for FLASH tool INTEGREX e-H [11] 3rd zero point M5 M6 [6] [1] X-axis M5 X-axis [4] Machine [5] [0] 2nd zero point x [7] Dmax Zc z INTEGREX e-V I21/I22 X-axis M5 X-axis [8] [2] I21/I22 Z-axis [4] [9/10] User-specified fixed point 1/2 2nd [7] [0] z [5] Zc Dmax x

When a FLASH tool is used, specify the position for indexing the tool, namely, the tool change command output position for indexing the tool of the same TNo. at the same B-axis angle during programmed operation. In all other cases, the tool change position specified by SU10 becomes valid. I21/I22 Z-axis Zc : Stock material edge projection length Dmax : Stock material maximum outside Z-axis x : Tool turning clearance (X-axis) SU50 [3] + B-axis spindle edge offset value z : Tool turning clearance (Z-axis) SU51 zero point 1 Machine zero point Clearance position 2 Clearance position Machine zero point 3 Machine zero point Machine zero point 4 2nd zero point 2nd zero point 3rd zero point M6 X-axis Machine 7 Clearance position zero point [3] machining M5 point 1 point 1 Z-axis zero point [1] 1. Do not use the setting of TC62 = 4 for the INTEGREX e- series. A collision with the ATC cover is likely to occur since the ATC position specified in fixed-point [6] M5 is present inside the ATC cover. 2. Since x in the case of TC62 = 0, 2, or 5 includes spindle tool length, if the tool is too long (as in the case of a long boring bar), the tool change operation may be software-limited in the +X direction. 3. TC62 = 5 or 6, Z-axis tool change command output position is identical with the end point of previous machining. In the case below, however, this may not As shown here, if the longest tool comes into the hatched portion, the position will escape in Z-axis direction by the distance determined by SU51.

Setting

Setting range0 to 11

Unit—

Program typeM

Takes effectImmediate

Source

Mazak PARAMETER LIST / ALARM LIST / M-CODE LIST, manual HA64HA0035E, p. 52, 336, 337. Reference and explanation only — not a reproduction of the manual.

Not sure what to set? Ask the Mazatrol assistant →