Every Mazak
alarm code.

1,197 alarms from the Mazak manual — 649 critical, 68 warning, 480 notice. Tap a code for its cause, what to do, and how to clear it.

1. 1EMERGENCY STOP■CRT
2. 2EMERGENCY STOP■CRT
3. 3EMERGENCY STOP■CRT
4. 4CORRECTABLE ECC ERROR■CRT
5. 5SYSTEM SOFTWARE ERROR■CRT
6. 6REMOTE I/O ERROR■CRT
7. 7SRAM MALFUNCTION■CRT
8. 8RAM MALFUNCTION■CRT
9. 9ABSOLUTE POSITION MALFUNCTION■CRT
10. 10DETECTOR MALFUNCTION (Alarm No., Axis, )■CRT
11. 11POSITION REFERENCE MALFUNCTION (Alarm No., Axis, )■CRT
12. 12SERVO BATTERY WARNING (Alarm No., Axis, )●NTC
13. 13PRE-PROCESSOR MALFUNCTION■CRT
14. 21SYSTEM ERROR■CRT
15. 22AMPLIFIER NOT EQUIPPED■CRT
16. 25SAFE OPERATION SYSTEM ALARM■CRT
17. 26SPINDLE SAFE OPER. SYSTEM ALARM■CRT
18. 30POWER SUPPLY MALFUNCTION■CRT
19. 31SERVO MALFUNCTION 1■CRT
20. 32SERVO PARAMETER MALFUNCTION■CRT
21. 33SERVO MALFUNCTION 2■CRT
22. 34SERVO MALFUNCTION 3■CRT
23. 35OVERLOAD■CRT
24. 41SPINDLE MALFUNCTION 1■CRT
25. 42SPINDLE PARAMETER MALFUNCTION■CRT
26. 43SPINDLE MALFUNCTION 2■CRT
27. 44SPINDLE MALFUNCTION 3■CRT
28. 51E2ROM MALFUNCTION●NTC
29. 52BATTERY ALARM●NTC
30. 53NC TEMPERATURE WARNING (Note 1, Note 2, Note 3)●NTC
31. 54DIO5V MALFUNCTION■CRT
32. 55REMOTE I/O ERROR (Note 1, Note 2, )■CRT
33. 56SYSTEM SOFTWARE CHECKING■CRT
34. 57NO PLC■CRT
35. 58CORRUPT PLC■CRT
36. 59PLC STOPPED■CRT
37. 60REMOTE I/O VER2.0 ERROR (System, station, )■CRT
38. 61REMOTE I/O INITIALIZE ERROR (No., System, )■CRT
39. 62RI/O ARBITRARY ALLOTMENT ERROR (No., Register number, )■CRT
40. 63ARBITRARY ALLOTMENT PARACHK ERR (No., Register number, )●NTC
41. 64HIGH SPEED DIO SETTING OVER (Threshold value, Number of excesses, )■CRT
42. 65OVER VOLTAGE DETECT●NTC
43. 66PARAMETER MALFUNCTION■CRT
44. 67HI-SPEED SYNCTAP AXIS ALARM■CRT
45. 68HI-SPEED SYNCTAP SPDL ALARM■CRT
46. 71ILLEGAL SERVO PARAMETER■CRT
47. 72SERVO WARNING■CRT
48. 81ILLEGAL SPINDLE PARAMETER■CRT
49. 82SPINDLE WARNING■CRT
50. 98H/W SYSTEM DISAGREEMENT ERROR■CRT
51. 101SOFT LIMIT (Axis, )▲WRN
52. 113OVER TRAVEL (Axis, )■CRT
53. 121SP ROT. FLUCT. ACCEL. CLAMP●NTC
54. 122SPINDLE ROT. FLUCTUATION N/A■CRT
55. 123SP ROT. FLUCT. SETTING ERROR (Alarm No., )■CRT
56. 124SP ROT. FLUCT. ILLEGAL COMMAND (Alarm No., )■CRT
57. 125ILLEGAL AXIS EXISTS■CRT
58. 126AXIS HAS NOT PASSED Z PHASE■CRT
59. 127ILLEGAL DIR. FOR ORIGIN RETURN■CRT
60. 128OUTSIDE INTERLOCK AXIS■CRT
61. 129INSIDE INTERLOCK AXIS■CRT
62. 130NO OPERATION MODE■CRT
63. 131CUTTING FEED OVERRIDE SET AT 0▲WRN
64. 132FEEDRATE ZERO▲WRN
65. 133STOP SPINDLE▲WRN
66. 134SPINDLE ROTATION EXCEEDED■CRT
67. 135BLOCK START INTERLOCK▲WRN
68. 136CUTTING BLOCK START INTERLOCK▲WRN
69. 137DYNAMIC COMPENSATION EXCEEDED■CRT
70. 138CANNOT ROTATE TABLE■CRT
71. 139PRE-INTERP ACCEL/DECEL ERROR■CRT
72. 140ILLEGAL REFERENCE RETURN No.▲WRN
73. 141EXCESS SIMULTANEOUS ERROR▲WRN
74. 142NONE OR DUPLICATE OPERAT. MODE▲WRN
75. 143ILLEGAL HANDLE FEED AXIS▲WRN
76. 144ILLEGAL CYCLE START (Alarm No., )■CRT
77. 145REQUIRE ABSOLUTE RECOVERY (Alarm No., )▲WRN
78. 146NOT AUTO MODE▲WRN
79. 147SHAPING AXIS TURNING ANGLE OVER (WNo., NNo., BNo.)▲WRN
80. 148CHUCK BARRIER (Note 1, Note 2, )■CRT
81. 149TAILSTOCK BARRIER (Note, )■CRT
82. 150WORK PIECE BARRIER■CRT
83. 151NO TANDEM CONTROLLING OPTION■CRT
84. 152ILLEGAL SYNCHRONIZED AXIS NAME■CRT
85. 153TRANSFER/PUSH UNFINISHED■CRT
86. 154ZERO RET. NOT ALLOWED (G58 MODE)●NTC
87. 155BARRIER TURRET/TOOL HEAD (Note, )■CRT
88. 156ILLEGAL MEASURING SENSOR SIGNAL■CRT
89. 157MEASURED RESULT MALFUNCTION■CRT
90. 158ILLEGAL COMMAND CROSS MACHINING▲WRN
91. 159CROSS MACHINING IMPOSSIBLE (Alarm No., )■CRT
92. 160ILLEGAL NUMBER OF CROSS AXIS■CRT
93. 161SUPERPOSITION CTRL IMPOSSIBLE (WNo., UNo., SNo.)■CRT
94. 162ILLEGAL SUPERPOSITION PARAMETER (WNo., UNo., SNo.)■CRT
95. 163BARRIER WORK (WNo., UNo., SNo.)■CRT
96. 164ILLEGAL CMD SAFE OPER SYS ALARM▲WRN
97. 165CANNOT MAKE SAFE OPER SYS ACTIVE●NTC
98. 166LOWER TURRET ALREADY ASSIGNED■CRT
99. 167ILLEGAL OPER TOOL TIP PT CTRL●NTC
100. 168ILLEGAL OPER 5X RADIUS COMP.●NTC
101. 169ILLEGAL OPER.HIGH SMOOTHING CTR●NTC
102. 170W AXIS THRUST FORCE ALARM■CRT
103. 171ILLEGAL W AXIS COMMAND■CRT
104. 172B AXIS NOT AVAILABLE■CRT
105. 1732ND SPDL C AXIS NOT AVIALABLE■CRT
106. 1742ND SPDL 1/10000 N/A■CRT
107. 175TABLE UNBALANCE CHECK N/A■CRT
108. 176CANNOT CHANGE TIME CONSTANT (System No., )■CRT
109. 177ONE-TOUCH TUNING IMPOSSIBLE (System No., )■CRT
110. 178INERTIA TOO LARGE (System No., )■CRT
111. 179CANNOT AUTO MEASURE INERTIA (System No., )■CRT
112. 180SYNCHRO TAP ILLEGAL COMMAND (WNo., UNo., SNo.)■CRT
113. 181NO MDI DATA (System No., )●NTC
114. 182CANNOT DETACH AXIS (Axis, UNo., SNo.)■CRT
115. 183CANNOT MDI INTERRUPT●NTC
116. 184ILLEGAL OPER IN G54.4 MODE●NTC
117. 185ILLEGAL OPER IN G68.2 MODE●NTC
118. 186W-THERMAL COMP. OVER LIMIT●NTC
119. 187SET W-THERMAL COMP. TOOL LENGTH●NTC
120. 188SET W-THERMAL COMP. REF. POINT■CRT
121. 189ILLEGAL SPINDLE DIRECTION (WNo., UNo., )■CRT
122. 191FILE SYSTEM I/O ERROR (Alarm No., )■CRT
123. 192EXECUTION IMPOSSIBLE (WNo., UNo., SNo.)■CRT
124. 193NO TOOL IN MAGAZINE (WNo., UNo., SNo.)■CRT
125. 194NO TOOL DATA IN PROGRAM (WNo., UNo., SNo.)■CRT
126. 195WRONG MEASURING DIRECTION■CRT
127. 196WRONG MEASURING POINT■CRT
128. 197UNREGISTERED HEAD DATA■CRT
129. 198NO HEAD DATA■CRT
130. 199DIVISION BY ZERO■CRT
131. 200HYDRAULIC UNIT PRESSURE DOWN■CRT
132. 201CHILLER MALFUNCTION■CRT
133. 202AIR PRESSURE DOWN■CRT
134. 203SPINDLE OIL PRESSURE DOWN■CRT
135. 204SPINDLE OIL LOW▲WRN
136. 206SPINDLE LUB. CHILLER MALF.■CRT
137. 207IRREGULAR SLIDEWAY OIL PRESSURE■CRT
138. 208SLIDEWAY OIL LOW▲WRN
139. 212MAGAZINE DRUM MALFUNCTION■CRT
140. 214ILLEGAL TOOL DESIGNATED■CRT
141. 216TOOL UNCLAMP OK?●NTC
142. 217THERMAL TRIP■CRT
143. 219MAIN TRANSFORMER OVERHEAT■CRT
144. 222AFC OVERLOAD■CRT
145. 224ILLEGAL TOOL FOR TOOL LGTH MEAS●NTC
146. 225TOOL LIFE OVER■CRT
147. 226TOOL BREAKAGE■CRT
148. 227SIMULTANEOUS M CODE OPERATION▲WRN
149. 228ILLEGAL M CODE▲WRN
150. 229INVALID SCREEN FOR CYCLE START■CRT
151. 230ILLEGAL MMS UNIT■CRT
152. 231EXTERNAL CONTROLLER ALARM■CRT
153. 232DOOR LOCK UNIT MALFUNCTION■CRT
154. 235MAGAZINE MANUAL INTERRUPT●NTC
155. 237MAGAZINE DOOR OPENED●NTC
156. 238AUTO TOOL CHANGE STOP●NTC
157. 240OPERATION RESTART UNFINISHED▲WRN
158. 242SPINDLE ORIENT TIME OVER■CRT
159. 253SKIP SENSOR MALFUNCTION■CRT
160. 256TOOL CLAMP SENSOR MALFUNCTION■CRT
161. 257TOOL UNCLAMP SENSOR MALFUNCTION■CRT
162. 258ATC COVER SENSOR(OPEN) MALF.▲WRN
163. 259ATC COVER SENSOR(CLOSE) MALF.▲WRN
164. 262GEAR SENSOR(HIGH SPEED) MALF.■CRT
165. 264GEAR SENSOR(LOW SPEED) MALF.■CRT
166. 265NEUTRAL SENSOR MALFUNCTION■CRT
167. 270X AXIS ORIGIN RETURN UNFINISH●NTC
168. 271Y AXIS ORIGIN RETURN UNFINISH●NTC
169. 272Z AXIS ORIGIN RETURN UNFINISH●NTC
170. 274SPDL CANNOT ROT(UNCLAMPED TOOL)▲WRN
171. 276SPDL CANNOT ROT(ATC ARM POS)●NTC
172. 278MPG SPECIAL MODE SELECT●NTC
173. 279MPG WARNING●NTC
174. 280NO ORIENT (UNCLAMPED TOOL)●NTC
175. 282NO ORIENT (ATC ARM POS. ERROR)●NTC
176. 283NOT UNCLAMPED (NOT STOP SPINDLE)●NTC
177. 284NOT UNCLAMPED (SPDL ORI. UNFIN)●NTC
178. 285NOT UNCLAMPED (NOT MANUAL MODE)●NTC
179. 289NO TOOL LOAD(ARM/SFTER POS ERR)●NTC
180. 291NO TOOL UNLOAD (TOOL IN MAG.)●NTC
181. 292NO UNLOAD (ARM/SHIFTER POS ERR)●NTC
182. 294NO TOOL SELECT (INCORRECT TNo.)●NTC
183. 295NO TOOL SELECT(ARM/SFT POS ERR)●NTC
184. 297NO SPINDLE START(GEAR POS ERR)▲WRN
185. 298NO SPINDLE ORIENT(GEAR POS ERR)▲WRN
186. 300BREAKER TRIP■CRT
187. 301CHILLER UNIT MALFUNCTION▲WRN
188. 304HIGH PRESS. PUMP THERMAL TRIP▲WRN
189. 306SPINDLE INHIBIT■CRT
190. 307MILL SPINDLE INHIBIT■CRT
191. 309SPINDLE ORIENT TIM OVER▲WRN
192. 310SPINDLE MISS CHUCK■CRT
193. 311SPINDLE CHUCK TIME OVER▲WRN
194. 312CHUCK FOOT SWITCH MALFUNCTION●NTC
195. 313SELECT CHUCK INT-EXT●NTC
196. 314CHUCK SENSOR MALFUNCTION■CRT
197. 315CHUCK PRESSURE LOW■CRT
198. 316CHUCK INT-EXT SELECT INHIBIT■CRT
199. 317C AXIS CONNECTION TIME OVER▲WRN
200. 318C AXIS SENSOR MALFUNCTION●NTC
201. 319B AXIS SENSOR MALFUNCITON▲WRN
202. 320B AXIS ROTATION INHIBIT■CRT
203. 321TOOL EYE EXTEND INHIBIT■CRT
204. 322TOOL EYE ARM POSITION NG▲WRN
205. 323TOOL EYE ARM POS. SENSOR MALF.▲WRN
206. 329TAIL SPINDLE TIME OVER▲WRN
207. 332FRONT DOOR SENSOR MALFUNCTION▲WRN
208. 333FRONT DOOR ACT. TIME OVER▲WRN
209. 334AXIS MOVE INHIBIT■CRT
210. 335ATC SHIFTER ACTION●NTC
211. 337DRIVE MODE CHANGE INHIBIT●NTC
212. 339ATC COVER ACT.TIME OVER▲WRN
213. 340ATC CONTROLLER MALFUNCTION■CRT
214. 341SHIFTER CONTROLLER MALF.■CRT
215. 342CARRIER CONTROLLER MALF.■CRT
216. 343RAPID MODE INHI. (HOME RETURN)●NTC
217. 344DRIVE MODE NG (HOME RETURN)●NTC
218. 345START ERR(DOOR OPEN/SET UP SW.)●NTC
219. 347START ERROR (ATC COVER OPEN)●NTC
220. 348START ERROR (MG COVER OPEN)●NTC
221. 349START ERROR (TOOL UNCLAMP)●NTC
222. 350START ERROR (TOOL EYE EXT.)●NTC
223. 351START ERROR (SPINDLE MISS CHUCK)●NTC
224. 352START ERROR(TAIL SPINDLE POS.)●NTC
225. 354START ERROR (ATC ARM POSITION)●NTC
226. 357TOOL SHIFTER&CARRIER POSI.ERROR●NTC
227. 358LINE FILTER WARNING●NTC
228. 359ATC ARM INHIBIT●NTC
229. 360C/S ERROR(CHIP No. MISS MATCH)●NTC
230. 361START ERROR (SET UP SWITCH)■CRT
231. 362AXIS SYNCHRO. ALARM■CRT
232. 363OVERLOAD DETECTION■CRT
233. 364C AXIS LUBE PRESSURE LOW■CRT
234. 365C AXIS LUBE LEVEL LOW■CRT
235. 366MILL CLAMP INVALID (NOT ORIENT)■CRT
236. 368MILL UNCLAMP INV. (TOOL UNCLAMP)■CRT
237. 369SPINDLE SYNCHRO INHIBIT■CRT
238. 370DOOR UNLOCK INHIBIT(COND.MISS)●NTC
239. 371COND. MISSING (SET UP SWITCH)■CRT
240. 372HIGH PRESS. COOL SYSTEM ALARM■CRT
241. 373HIGH PRE COOL SYS. PRE. ALARM■CRT
242. 374COOLANT LEVEL TOO LOW■CRT
243. 376WORK NO. SEARCH ERROR▲WRN
244. 377WORK NO. SET ERROR▲WRN
245. 378WARMING UP !!●NTC
246. 379WARMING UP ERROR■CRT
247. 381MAINTENANCE DOOR OPEN●NTC
248. 382OPERATING PANEL POS. UNSUITABLE■CRT
249. 383SPINDEL GEAR LUBE PRE ALARM■CRT
250. 384SPINDLE GEAR LUBE LEVEL LOW■CRT
251. 385TAIL CONDITION ALARM■CRT
252. 386TAIL POSITION MALFUNCTION■CRT
253. 387TAIL DATA ILLEGAL■CRT
254. 389SCALE F/B AIR PRESSURE DOWN●NTC
255. 390BATTERY VOLTAGE LOW●NTC
256. 391SAVING ENERGY MODE●NTC
257. 392THERMAL DISPLACEMENT OFFSET ER■CRT
258. 394START ERROR(CHUCK OPEN)■CRT
259. 395ATC MALFUNCTION■CRT
260. 397OPERATING SWITCH FAULT■CRT
261. 398MOTOR&SERVO POWER OFF FAULT■CRT
262. 401ILLEGAL FORMAT●NTC
263. 402ILLEGAL NUMBER INPUT●NTC
264. 403PROGRAM TOO LARGE●NTC
265. 404MEMORY CAPACITY EXCEEDED●NTC
266. 405PROGRAM No. NOT FOUND●NTC
267. 406MEMORY PROTECT●NTC
268. 407DESIGNATED DATA NOT FOUND●NTC
269. 408PROGRAM ERROR●NTC
270. 409ILLEGAL INSERTION●NTC
271. 410ILLEGAL DELETION●NTC
272. 411POWER OFF DURING PROGRAM EDIT●NTC
273. 412SUB PROGRAM NESTING EXCEEDED●NTC
274. 413MAX. No. OF REGIST PROG EXCEEDED●NTC
275. 414AUTO CALCULATION IMPOSSIBLE (No., )●NTC
276. 415MIS-SET G CODE●NTC
277. 416AUTO PROCESS IMPOSSIBLE●NTC
278. 417EDITING PROHIBITED●NTC
279. 418EIA/ISO CONVERTING●NTC
280. 419AUTO TAP PROCESS IMPOSSIBLE●NTC
281. 420SAME DATA EXISTS●NTC
282. 421DATA NOT FOUND●NTC
283. 422MEMORY PROTECT (I/O BUSY)●NTC
284. 423MAX NUMBER OF TOOLS EXCEEDED●NTC
285. 424ALL POCKET NUMBERS NOT ASSIGNED●NTC
286. 425DATA MISSING●NTC
287. 426PROGRAM DATA MISSING●NTC
288. 427MEMORY PROTECT (AUTO MODE)●NTC
289. 428MEMORY PROTECT (AUTO OPERATION)●NTC
290. 429CANNOT PERFORM MEASUREMENT●NTC
291. 430ILLEGAL TOOL DESIGNATED●NTC
292. 431ILLEGAL PALLET No.●NTC
293. 432ILLEGAL TOOL No.●NTC
294. 433SAME PROGRAM EXISTS●NTC
295. 434NO ASSIGNED TOOL IN TOOL FILE●NTC
296. 435PROGRAM CHECK NOT ALLOWED●NTC
297. 436UNREGISTERED TNo.●NTC
298. 437NO NOM-φ DATA IN PROGRAM●NTC
299. 438END UNIT NOT FOUND●NTC
300. 439MAZATROL PROGRAM DESIGNATED●NTC
301. 440EIA/ISO PROGRAM DESIGNATED●NTC
302. 441UNREGISTERED HEAD DATA●NTC
303. 442DATA RENEWAL NOT ALLOWED●NTC
304. 443HELP IS NOT AVAILABLE●NTC
305. 444EDITING PROHIBITED AREA●NTC
306. 445ILLEGAL UNIT●NTC
307. 446RESTART TIMES EXCEEDED●NTC
308. 447PROGRAM ERROR●NTC
309. 448RESTART SEARCH UNFINISHED▲WRN
310. 449RESTART SEARCH FINISHED●NTC
311. 450TOUCH SENSOR NOT IN SPINDLE●NTC
312. 451SAME MATERIAL ENTERED●NTC
313. 452NO SHAPE DATA IN UNIT●NTC
314. 453NO SHAPE DATA TO COPY IN UNIT●NTC
315. 454CURSOR POSITION INCORRECT●NTC
316. 455SAME PROGRAM No. DESIGNATED●NTC
317. 456NO TOOL IN SPINDLE●NTC
318. 457DATA ADDRESS NOT FOUND●NTC
319. 458INTERFERING TOOL REGISTERED●NTC
320. 459DISPLAY PROTECT●NTC
321. 461PRIORITY No. OVERLAP (WNo., UNo., SNo.)●NTC
322. 462ILLEGAL PRIORITY NUMBER (WNo., UNo., SNo.)●NTC
323. 463PRIORITY No. OVERFLOW●NTC
324. 464ILLEGAL ADDRESS INPUT●NTC
325. 465EIA SHAPE DATA NOT FOUND●NTC
326. 466INCORRECT EIA SHAPE DATA●NTC
327. 468MAINTENANCE CHECK WARNING●NTC
328. 469TPC DATA EDIT IMPOSSIBLE●NTC
329. 470ILLEGAL TPC DATA●NTC
330. 471TPC DATA NOT FOUND●NTC
331. 472CALCULATION ERROR●NTC
332. 473FINAL POINT DATA NOT FOUND●NTC
333. 474NO PROGRAM DISPLAY (TAPE MODE)●NTC
334. 475NO EIA/ISO OPTION●NTC
335. 476NO OPTION●NTC
336. 477DESCRIPTION IMPOSSIBLE●NTC
337. 478MEMORY PROTECT (MEASURING)●NTC
338. 480UNIT NOT SELECTED (No., )■CRT
339. 481DIRECTORY NOT FOUND●NTC
340. 484INCORRECT SPINDLE TOOL●NTC
341. 485INCORRECT HEAD INDEX ANGLE●NTC
342. 486ILLEGAL JAW DATA●NTC
343. 487LONG BORING BAR ADAPTER EXISTS (Pocket No., )●NTC
344. 488MEMORY PROTECT (MAGAZINE SETUP)●NTC
345. 489CANNOT SET THREAD POSITION●NTC
346. 490REGISTRATION NUMBER EXCEEDED●NTC
347. 491ITEM NOT SETUP●NTC
348. 492CANNOT EDIT 3D DATA●NTC
349. 493SELECT JAW TYPE●NTC
350. 494CANNOT SELECT TNO (NOT MAGAZINE)●NTC
351. 495INCORRECT CAD MODEL DATA (Note, )●NTC
352. 497HEAD ANGLE INCORRECT●NTC
353. 498NO HEAD DATA●NTC
354. 499ILLEGAL HEAD TYPE●NTC
355. 501ILLEGAL FORMAT●NTC
356. 502CANNOT LOAD (PROG SIZE EXCEED) (WNo., )●NTC
357. 503CANNOT LOAD (TOO MANY PROGRAMS) (WNo., )●NTC
358. 504CANNOT LOAD (AUTO OPERATION)●NTC
359. 505CANNOT LOAD (MISMATCH)●NTC
360. 506SAME PROGRAM No. DESIGNATED (WNo., )●NTC
361. 507NO DESIGNATED PROGRAM (WNo., )●NTC
362. 508MEMORY CAPACITY EXCEEDED (WNo., )●NTC
363. 509MEMORY PROTECT●NTC
364. 510DATA DO NOT MATCH (WNo., )●NTC
365. 511PROGRAM DATA NOT SAME (WNo., UNo., SNo.)●NTC
366. 512NO EIA/ISO OPTION (WNo., )●NTC
367. 513PROGRAM DATA TYPE INCORRECT●NTC
368. 514DATA TYPE INCORRECT●NTC
369. 515INCORRECT DESIGNATED DATA●NTC
370. 516SYSTEM ERROR●NTC
371. 517PROG. OPERATION NOT ALLOWED (WNo., )●NTC
372. 518DATA OPERATION NOT ALLOWED●NTC
373. 519DATA SIZE EXCEEDED (WNo., Note, )●NTC
374. 520EIA/ISO CONVERT ERROR (WNo., )●NTC
375. 521CANNOT LOAD (WRONG PROG TYPE)●NTC
376. 522SAME SET No. EXISTS●NTC
377. 523IMPOSSIBLE TO CONVERT EIA (Prg No. Processing No., )●NTC
378. 525HDD I/O ERROR (Cause, )▲WRN
379. 526PROFIBUS-DP COMMUNICATION ERROR (Note 1, Note 2, )●NTC
380. 527ETHERNET/IP COMMUNICATION ERROR (Note 1, Note 2, )●NTC
381. 528FIELDNETWORK SETTING ERROR (Note 1, Note 2, )●NTC
382. 529CC-LINK COMMUNICATION ERROR (No. )●NTC
383. 530CMT MIS-CONNECTED ( )●NTC
384. 531DESIGNATED FILE NOT FOUND (WNo. )●NTC
385. 532CMT NOT CONNECTED ( )●NTC
386. 533NO OPERABLE DATA IN CMT ( )●NTC
387. 534CMT I/O ERROR●NTC
388. 535CMT WRITE PROTECT●NTC
389. 536POWER OFF DURING CMT OPERATION●NTC
390. 537CMT MALFUNCTION●NTC
391. 538CC-LINK UNCONNECTED●NTC
392. 539—●NTC
393. 540TAPE READER MIS-CONNECTED●NTC
394. 541TAPE PUNCHER MIS-CONNECTED●NTC
395. 542NO TAPE READER PUNCHER OPTION●NTC
396. 543WNo. NOT FOUND ON PAPER TAPE●NTC
397. 544SET NEW PAPER TAPE●NTC
398. 545POWER OFF TAPE READ/PUNCH OPER.●NTC
399. 546TAPE READER ERROR●NTC
400. 547TAPE PUNCHER ERROR●NTC
401. 548MAZATROL PROGRAM DESIGNATED●NTC
402. 549DESIGNATED DATA NOT FOUND●NTC
403. 550PARITY H ERROR●NTC
404. 551PARITY V ERROR●NTC
405. 552PROGRAM END NOT FOUND●NTC
406. 553WORK No. UNITS EXCEEDED●NTC
407. 554POWER OFF IN EIA/ISO CONVERT●NTC
408. 555—●NTC
409. 556—●NTC
410. 557DESIGNATED DIRECTORY NOT FOUND■CRT
411. 563PRINTER I/O ERROR (Cause, )●NTC
412. 564—●NTC
413. 565ID MIS-CONNECTED●NTC
414. 566POWER STOPPED DURING ID OPER.●NTC
415. 567ID I/O ERROR●NTC
416. 568IBS COMMUNICATION ERROR (Note 1, Note 2, )▲WRN
417. 569—●NTC
418. 570NO DNC OPTION●NTC
419. 571ILLEGAL FORMAT●NTC
420. 572CANNOT LOAD (PROG SIZE EXCEED) (WNo. )●NTC
421. 573CANNOT LOAD (TOO MANY PROGRAMS) (WNo. )●NTC
422. 574CANNOT LOAD (AUTO OPERATION)●NTC
423. 575CANNOT LOAD (MISMATCH)●NTC
424. 576SAME PROGRAM No. DESIGNATED (WNo. )●NTC
425. 577NO DESIGNATED PROGRAM (WNo. )●NTC
426. 578MEMORY CAPACITY EXCEEDED (WNo. )●NTC
427. 579MEMORY PROTECT●NTC
428. 580---●NTC
429. 581---●NTC
430. 582DESIGNATED FILE NOT TRANSFERRED●NTC
431. 583PROGRAM DATA TYPE INCORRECT●NTC
432. 584RECEIVED DATA TYPE INCORRECT●NTC
433. 585CABLE MIS-CONNECTED●NTC
434. 586SYSTEM ERROR●NTC
435. 587PROG. OPERATION NOT ALLOWED (WNo. )●NTC
436. 588DATA OPERATION NOT ALLOWED●NTC
437. 589DATA SIZE EXCEEDED (WNo., Note, )●NTC
438. 590DNC COMMAND IMPOSSIBLE●NTC
439. 591NO OPTION (WNo., )●NTC
440. 592ILLEGAL COMMAND RECEIVED●NTC
441. 593DNC I/O ERROR●NTC
442. 594SEND-RECEIVE ERROR●NTC
443. 595FILE TRANSFER ERROR●NTC
444. 596DNC MALFUNCTION●NTC
445. 597POWER OFF DURING DNC OPERATION●NTC
446. 598NO EIA/ISO OPTION●NTC
447. 599DESIGNATED DATA NOT FOUND●NTC
448. 600—●NTC
449. 601SYSTEM ERROR■CRT
450. 602PROG. OPERATION NOT ALLOWED■CRT
451. 603NO DESIGNATED PROGRAM (WNo., UNo., SNo.)■CRT
452. 604NO PITCH IN MULTI WORKPIECES (WNo., UNo., SNo.)■CRT
453. 605NO TOOL DATA IN PROGRAM (WNo., UNo., SNo.)■CRT
454. 606NO FIGURE IN PROGRAM (WNo., UNo., SNo.)■CRT
455. 607MISSING INPUT DATA (POINT) (WNo., UNo., SNo.)■CRT
456. 608MISSING INPUT DATA (LINE) (WNo., UNo., SNo.)■CRT
457. 609MISSING INPUT DATA (FACE) (WNo., UNo., SNo.)■CRT
458. 610MISSING TOOL DATA FOR POINT (WNo., UNo., SNo.)■CRT
459. 611MISSING TOOL DATA FOR LINE (WNo., UNo., SNo.)■CRT
460. 612MISSING TOOL DATA FOR FACE (WNo., UNo., SNo.)■CRT
461. 613DATA MISSING IN WPC UNIT (WNo., UNo., SNo.)■CRT
462. 614SUB PROGRAM NESTING EXCEEDED (WNo., UNo., SNo.)■CRT
463. 615DATA MISSING IN OFFSET UNIT (WNo., UNo., SNo.)■CRT
464. 616DATA ERROR IN M CODE UNIT (WNo., UNo., SNo.)■CRT
465. 617EXECUTION IMPOSSIBLE (WNo., UNo., SNo.)■CRT
466. 618POINT CUTTING PARAMETER ERROR (WNo., UNo., SNo.)■CRT
467. 619LINE/FACE CUTTING PAR. ERROR (WNo., UNo., SNo.)■CRT
468. 620CUTTING SPEED ZERO (WNo., UNo., SNo.)■CRT
469. 621FEEDRATE ZERO (WNo., UNo., SNo.)■CRT
470. 622DESIGNATED UNIT NOT FOUND■CRT
471. 623DESIGNATED SNo. NOT FOUND■CRT
472. 624RESTART IMPOSSIBLE■CRT
473. 625ENDMILL DIAMETER EXCEEDED (WNo., UNo., SNo.)■CRT
474. 626DESIGNATED TOOL NOT FOUND (WNo., UNo., SNo.)■CRT
475. 627TOOL DATA INPUT PROCESS ERROR (WNo., UNo., SNo.)■CRT
476. 628NO ASSIGNED TOOL IN TOOL FILE (WNo., UNo., SNo.)■CRT
477. 629TOOL FILE INPUT PROCESS ERROR (WNo., UNo., SNo.)■CRT
478. 630Z DEPTH OF CUT TOO LARGE (WNo., UNo., SNo.)■CRT
479. 631STOCK REMOVAL R TOO LARGE (WNo., UNo., SNo.)■CRT
480. 632RADIAL DEPTH OF CUT ZERO (WNo., UNo., SNo.)■CRT
481. 633Z DEPTH OF CUT ZERO (WNo., UNo., SNo.)■CRT
482. 634FINISH DEPTH OF CUT ZERO (WNo., UNo., SNo.)■CRT
483. 635TOOL DIAMETER ZERO (WNo., UNo., SNo.)■CRT
484. 636STOCK REMOVAL Z TOO SMALL (WNo., UNo., SNo.)■CRT
485. 637STOCK REMOVAL R TOO SMALL (WNo., UNo., SNo.)■CRT
486. 638R DEPTH OF CUT TOO LARGE (WNo., UNo., SNo.)■CRT
487. 639DESIGNATED PALLET NOT FOUND (WNo., UNo., SNo.)■CRT
488. 640ILLEGAL INDEX ANGLE INPUT (WNo., UNo., SNo.)■CRT
489. 641MISSING INPUT DATA (WNo., UNo., SNo.)■CRT
490. 642ILLEGAL NEXT PALLET No. INPUT (WNo., UNo., SNo.)■CRT
491. 643DATA ERROR IN MAN. PROG. UNIT (WNo., UNo., SNo.)■CRT
492. 644NOMINAL DIAMETER NOT FOUND (WNo., UNo., SNo.)■CRT
493. 645PRIORITY No. OVERLAP (WNo., UNo., SNo.)■CRT
494. 646ILLEGAL PRIORITY NUMBER (WNo., UNo., SNo.)* (LNo. 1, LNo. 2, )**■CRT
495. 647END UNIT NOT FOUND (WNo., UNo., SNo.)■CRT
496. 648MULTI OFFSET DATA TOO LARGE (WNo., UNo., SNo.)■CRT
497. 649MEASURING SEQUENCE INCOMPLETE (WNo., UNo., SNo.)■CRT
498. 650CHAMFERING IMPOSSIBLE (WNo., UNo., SNo.)■CRT
499. 651GEAR PARAMETER ERROR (WNo., UNo., SNo.)■CRT
500. 652GEAR SHIFT DATA ERROR (WNo., UNo., SNo.)■CRT
501. 653ILLEGAL TOOL DESIGNATED (WNo., UNo., SNo.)■CRT
502. 654TOOL DATA ERROR (WNo., UNo., SNo.)■CRT
503. 655PROGRAM DATA CORRUPT (WNo., UNo., SNo.)■CRT
504. 656MEASURING SEQ. DATA NOT FOUND (WNo., UNo., SNo.)■CRT
505. 657ILLEGAL NUMBER INPUT (WNo., UNo., SNo.)■CRT
506. 658INITIAL Z < MATERIAL DEPTH (WNo., UNo., SNo.)■CRT
507. 659NO TOOL PATH CHECK (I/O BUSY) (WNo., )●NTC
508. 660CANNOT MOVE DESIGNATED AXIS■CRT
509. 661ILLEGAL M CODE (WNo., UNo., SNo.)■CRT
510. 662NO INCLINED PLANE OPTION (WNo., UNo., )■CRT
511. 663WRONG HEAD ANGLE (WNo., UNo., )■CRT
512. 6643-D UNIT NOT FOUND IN PROGRAM (WNo., UNo., SNo.)■CRT
513. 665ILLEGAL DATA IN 3-D UNIT (WNo., UNo., SNo.)■CRT
514. 666PLANE DATA NOT FOUND IN PROGRAM (WNo., UNo., SNo.)■CRT
515. 667CHECK SURFACE DATA NOT FOUND (WNo., UNo., SNo.)■CRT
516. 668ILLEGAL PLANE DATA IN PROGRAM (WNo., UNo., SNo.)■CRT
517. 669ILLEGAL TOLERANCE DATA INPUT (WNo., UNo., SNo.)■CRT
518. 670ILLEGAL SEQUENCE DATA IN PRG. (WNo., UNo., SNo.)■CRT
519. 671ILLEGAL MOVE SURFACE DATA (WNo., UNo., SNo.)■CRT
520. 672ILLEGAL AREA DATA INPUT (WNo., UNo., SNo.)■CRT
521. 673FL NUMBER EXCEEDED (3-D UNIT) (WNo., UNo., SNo.)■CRT
522. 674NO 5FACE CUTTING OPTION (WNo., UNo., )■CRT
523. 675ILLEGAL CUTTING FACE DESIGNATED (WNo., UNo., SNo.)■CRT
524. 676ILLEGAL UNIT (WNo., UNo., )■CRT
525. 677UNREGISTERED HEAD DATA (WNo., UNo., )■CRT
526. 678NO INTERSECTION (WNo., UNo., SNo.)■CRT
527. 679CONNECTING CORNER IMPOSSIBLE (WNo., UNo., SNo.)■CRT
528. 680NUMBER OF HOLES EXCEEDED (>500) (WNo., UNo., SNo.)■CRT
529. 681CORNER R/C DEFINED AT SPT/FPT (WNo., UNo., SNo.)■CRT
530. 682ILLEGAL REPEAT FIGURE (WNo., UNo., SNo.)■CRT
531. 683UNDEFINED CORNER (WNo., UNo., SNo.)■CRT
532. 684POINT CUTTING PATTERN ERROR (WNo., UNo., SNo.)■CRT
533. 685SQUARE CANNOT BE DEFINED (WNo., UNo., SNo.)■CRT
534. 686NO STARTING POINT (WNo., UNo., SNo.)■CRT
535. 687NO FINISH POINT (WNo., UNo., SNo.)■CRT
536. 688INSUFFICIENT INPUT DATA (WNo., UNo., SNo.)■CRT
537. 689INPUT DATA TOO MANY (WNo., UNo., SNo.)■CRT
538. 690ILLEGAL RADIUS (WNo., UNo., SNo.)■CRT
539. 691MOUNT (VALLEY) SHAPE ERROR (WNo., UNo., SNo.)■CRT
540. 692MAX POINT NUMBER EXCEEDED (>200) (WNo., UNo., SNo.)■CRT
541. 693NUMBER OF SHAPES TOO LARGE (WNo., UNo., SNo.)■CRT
542. 694FIXED FIGURE DESIGNATED ERROR (WNo., UNo., SNo.)■CRT
543. 695POINT INSIDE CIRCLE (WNo., UNo., SNo.)■CRT
544. 696ILLEGAL DIRECTION (WNo., UNo., SNo.)■CRT
545. 697DATUM <P> REQUIRED (WNo., UNo., SNo.)■CRT
546. 698TWO POINTS OVERLAP (WNo., UNo., SNo.)■CRT
547. 699PARALLEL LINE (WNo., UNo., SNo.)■CRT
548. 700—●NTC
549. 701DEFINED SHAPE TOO SMALL (WNo., UNo., SNo.)▲WRN
550. 702FIGURE DEFINITION ERROR (WNo., UNo., SNo.)▲WRN
551. 703PROCESS DEFINITION ERROR (WNo., UNo., SNo.)●NTC
552. 704TOOL INTERFERENCE (WNo., UNo., SNo.)▲WRN
553. 705APPROACH POINT ERROR (WNo., UNo., SNo.)■CRT
554. 706ILLEGAL FIGURE DATA (WNo., UNo., SNo.)●NTC
555. 707CHAMFER CUTTER INTERFERENCE (WNo., UNo., SNo.)▲WRN
556. 708BLOCK DATA LIMIT EXCEEDED (WNo., UNo., SNo.)●NTC
557. 709CHECK DEPTH-R (WNo., UNo., SNo.)●NTC
558. 710CORNER ROUNDING CUTTER DIA ERR (WNo., UNo., SNo.)●NTC
559. 711UNIT DATA NOT FOUND (WNo., UNo., SNo.)■CRT
560. 712ILLEGAL UNIT DATA (WNo., UNo., SNo.)■CRT
561. 713SEQUENCE DATA NOT FOUND (WNo., UNo., SNo.)■CRT
562. 714ILLEGAL SEQUENCE DATA (WNo., UNo., SNo.)■CRT
563. 715ILLEGAL CUTTING POINT (WNo., UNo., SNo.)■CRT
564. 716ILLEGAL CUTTING START POINT (WNo., UNo., SNo.)■CRT
565. 717SHAPE EXCEEDS MATERIAL SIZE (WNo., UNo., SNo.)■CRT
566. 718CUTTING DIRECTION NOT DEFINED (WNo., UNo., SNo.)■CRT
567. 719REVERSE SHAPE CONTOUR (WNo., UNo., SNo.)■CRT
568. 720DOUBLE SHAPE CONTOUR (WNo., UNo., SNo.)■CRT
569. 721ILLEGAL RADIUS (WNo., UNo., SNo.)■CRT
570. 722ILLEGAL CORNER DEFINITION (WNo., UNo., SNo.)■CRT
571. 723EXCEEDS NUMBER OF SHAPES (WNo., UNo., SNo.)■CRT
572. 724EXCEEDS NUMBER OF VALLEY SHAPES (WNo., UNo., SNo.)■CRT
573. 725ILLEGAL COMMON DATA (RADIAL) (WNo., UNo., SNo.)■CRT
574. 726ILLEGAL COMMON DATA (AXIAL) (WNo., UNo., SNo.)■CRT
575. 727MATERIAL SHAPE CROSSING (WNo., UNo., SNo.)■CRT
576. 728EXCESSIVE FINISH ALLOWANCE (WNo., UNo., SNo.)■CRT
577. 729ILLEGAL SHAPE DESIGNATED (CNR) (WNo., UNo., SNo.)■CRT
578. 730ILLEGAL SHAPE DESIGNATED (EDG) (WNo., UNo., SNo.)■CRT
579. 731ILLEGAL NUM. OF PATHS (THR) (WNo., UNo., SNo.)■CRT
580. 732ACCELERATION DISTANCE EXCEED (WNo., UNo., SNo.)■CRT
581. 733ILLEGAL SHAPE DESIGNATED (GRV) (WNo., UNo., SNo.)■CRT
582. 734ILLEGAL SHAPE EXCEEDS MTRL SIZE (WNo., UNo., SNo.)■CRT
583. 735ILLEGAL DESIGNATED TL WID (GRV) (WNo., UNo., SNo.)■CRT
584. 736ILLEGAL OVERLAP (WNo., UNo., SNo.)■CRT
585. 737ILLEGAL DRILLING DIRECTION (WNo., UNo., SNo.)■CRT
586. 738CORNER (R/C) DESIGNATED OVERLAP (WNo., UNo., SNo.)■CRT
587. 739ILLEGAL FINISHING ALLOWANCE (WNo., UNo., SNo.)■CRT
588. 740ILLEGAL ANGLE IN FIRST SEQUENCE (WNo., UNo., SNo.)■CRT
589. 741ILLEGAL THREAD ANGLE (WNo., UNo., SNo.)■CRT
590. 742ILLEGAL THREAD HEIGHT (WNo., UNo., SNo.)■CRT
591. 743INTERSECTION NOT FOUND (WNo., UNo., SNo.)■CRT
592. 744DATA MISSING (INTERSECTION) (WNo., UNo., SNo.)■CRT
593. 745INTERSECTION CALCULATE IMPOSS. (WNo., UNo., SNo.)■CRT
594. 746NO DEPTH OF CUT INFO. (WNo., UNo., SNo.)■CRT
595. 747CHIP BREAKING CYCLE N/A (WNo., UNo., SNo.)■CRT
596. 748CANNOT MAKE T-PATH (CHK DEPTH) (WNo., UNo., SNo.)■CRT
597. 749CANNOT DRAW FIGURE●NTC
598. 750—●NTC
599. 751CURVE DEFINITION ERROR (WNo., UNo., SNo.)●NTC
600. 752DESIGNATED AREA DATA IMPOSSIBLE (WNo., UNo., SNo.)●NTC
601. 753SMALL TOOL (WNo., UNo., SNo.)●NTC
602. 754LARGE TOOL (WNo., UNo., SNo.)■CRT
603. 755R DIRECTION PITCH SMALL (WNo., UNo., SNo.)■CRT
604. 756Z DIRECTION PITCH SMALL (WNo., UNo., SNo.)■CRT
605. 757CURVE DEFINITION LARGE (WNo., UNo., SNo.)■CRT
606. 758INITIAL POINT SET ERROR (WNo., UNo., SNo.)■CRT
607. 759WPC UNIT NOT FOUND (MILL & TURN) (WNo., UNo., SNo.)■CRT
608. 760NO T. CENTER POINT IN WPC UNIT (WNo., UNo., SNo.)■CRT
609. 761HEAD ANGLE INCORRECT (C-AXIS) (WNo., UNo., SNo.)■CRT
610. 762PROGRAM IS NOT MILL & TURN TYPE (WNo., UNo., SNo.)■CRT
611. 763START PROCESS ILLEGAL (WNo., UNo., SNo.)■CRT
612. 764MAIN PRG/SUB PRG TYPE MISMATCH (WNo., UNo., SNo.)■CRT
613. 765Z-OFFSET NOT FOUND (WNo., UNo., SNo.)■CRT
614. 766MAXIMUM NO.OF LAYOUTS EXCEEDED (WNo., UNo., SNo.)■CRT
615. 767ILLEGAL ESCAPE TOOL No. (WNo., UNo., SNo.)■CRT
616. 7684 AXIS MACHINING PROGRAM ERROR (WNo., UNo., SNo.)■CRT
617. 769ILLEGAL TOOL DIRECTION/SPDL ROT (WNo., UNo., SNo.)■CRT
618. 770FIN LEN ERROR (CHECK COM UNIT) (WNo., UNo., SNo.)■CRT
619. 771ILLEGAL LOW TUR COMMON UNIT (WNo., UNo., SNo.)■CRT
620. 772NO HEAD UNIT IN PROGRAM (WNo., UNo., SNo.)■CRT
621. 773TRANSFER UNIT IN PROGRAM (WNo., UNo., SNo.)■CRT
622. 774HEAD UNIT IN PROGRAM (WNo., UNo., SNo.)■CRT
623. 775TOOL CANNOT PERFORM FACING (WNo., UNo., SNo.)■CRT
624. 776NO Y-AXIS (WNo., UNo., SNo.)■CRT
625. 777INCORRECT POSIT. CANNOT RESTART (WNo., UNo., SNo.)■CRT
626. 778INCORRECT POSIT. CANNOT START (WNo., UNo., SNo.)■CRT
627. 779—●NTC
628. 780APPROACH PATH INTERFERENCE (WNo., UNo., SNo.)■CRT
629. 781DBL SPDL OPER ILLEGAL TUR ASIGN (WNo., UNo., SNo.)■CRT
630. 782DBL SPDL OPER NO TRANS UNIT (WNo., UNo., SNo.)■CRT
631. 783DBL SPDL OP ILLEGAL SIMUL OP (WNo., UNo., SNo.)■CRT
632. 784DBL SPDL OP ILLEGAL BALANCE CUT (WNo., UNo., SNo.)■CRT
633. 785DBL SPDL OPER ILLEGAL TUR ESC (WNo., UNo., SNo.)■CRT
634. 786DBL SPDL OP ILLEGAL MEASUREMENT (WNo., UNo., SNo.)■CRT
635. 787DBL SPDL OPER ILLEGAL TRANSFER (WNo., UNo., SNo.)■CRT
636. 788DBL SPDL OPER ILLEGAL HEAD UNIT (WNo., UNo., SNo.)■CRT
637. 789DBL SPDL OPER UNIT ERROR (WNo., UNo., SNo.)■CRT
638. 790ILLEGAL BALANCE CUT (WNo., UNo., SNo.)■CRT
639. 791MUST INPUT CUTTING SPEED (WNo., UNo., SNo.)■CRT
640. 792MUST INPUT FEEDRATE (WNo., UNo., SNo.)■CRT
641. 793ILLEGAL MILL SPINDLE RPM (WNo., UNo., SNo.)■CRT
642. 794INCORRECT B AXIS POSITION (WNo., UNo., SNo.)■CRT
643. 795SHIFT-Y TOO LARGE ( , )■CRT
644. 796NO MAZATROL L TURRET OPT (WNo., UNo., SNo.)■CRT
645. 797BARRIER CANCEL ON (WNo., UNo., SNo.)■CRT
646. 798JAW NO NOT FOUND (WNo., UNo., SNo.)■CRT
647. 799—●NTC
648. 800—●NTC
649. 801SIMULTANEOUS AXIS EXCEEDED (WNo., NNo., BNo.)■CRT
650. 802ILLEGAL AXIS NAME (WNo., NNo., BNo.)■CRT
651. 803DIVIDED COMMAND ERROR (WNo., NNo., BNo.)■CRT
652. 804PARITY H ERROR (WNo., NNo., BNo.)■CRT
653. 805PARITY V ERROR (WNo., NNo., BNo.)■CRT
654. 806ILLEGAL ADDRESS (WNo., NNo., BNo.)■CRT
655. 807ILLEGAL FORMAT (WNo., NNo., BNo.)■CRT
656. 808MIS-SET G CODE (WNo., NNo., BNo.)■CRT
657. 809ILLEGAL NUMBER INPUT (WNo., NNo., BNo.)■CRT
658. 810PROGRAM END NOT FOUND (WNo., NNo., BNo.)■CRT
659. 811ILLEGAL O/N NUMBER (WNo., NNo., BNo.)■CRT
660. 812ERROR IN BUFFER BLOCK (WNo., NNo., BNo.)■CRT
661. 813INCH/METRIC OPTION NOT FOUND (WNo., NNo., BNo.)■CRT
662. 814INTERPOLATION OVERFLOW (WNo., NNo., BNo.)■CRT
663. 815G60 OPTION NOT FOUND (WNo., NNo., BNo.)■CRT
664. 816FEEDRATE ZERO (WNo., NNo., BNo.)■CRT
665. 817INCORRECT ARC DATA (WNo., NNo., BNo.)■CRT
666. 818MISSING CENTER (NO DATA) (WNo., NNo., BNo.)■CRT
667. 819HELICAL OPTION NOT FOUND (WNo., NNo., BNo.)■CRT
668. 820G02.1, G03.1 OPTION NOT FOUND (WNo., NNo., BNo.)■CRT
669. 821G07 OPTION NOT FOUND (WNo., NNo., BNo.)■CRT
670. 822ILLEGAL MODAL (WNo., NNo., BNo.)■CRT
671. 823G17 - G19 COMMAND IN M98 (WNo., NNo., BNo.)■CRT
672. 824G17 - G19 COMMAND IN G68 (WNo., NNo., BNo.)■CRT
673. 825G17 - G19 COMMAND IN G38 - G42 (WNo., NNo., BNo.)■CRT
674. 826G95 OPTION NOT FOUND (WNo., NNo., BNo.)■CRT
675. 827F0 COMMAND IN G02, G03 (WNo., NNo., BNo.)■CRT
676. 828NO AUTO CORNER OVERRIDE OPTION (WNo., NNo., BNo.)■CRT
677. 829ILLEGAL 2ND M CODE (WNo., NNo., BNo.)■CRT
678. 830G96 OPTION NOT FOUND (WNo., NNo., BNo.)■CRT
679. 831G45, 46, 47, 48 OPTION NOT FOUND (WNo., NNo., BNo.)■CRT
680. 832G45 - G49 COMMAND IN M98 (WNo., NNo., BNo.)■CRT
681. 8331/4, 3/4 CIRCLES IN G45 - G48 (WNo., NNo., BNo.)■CRT
682. 834G40, G41, G42 OPTION NOT FOUND (WNo., NNo., BNo.)■CRT
683. 835G41, G42, FORMAT ERROR (WNo., NNo., BNo.)■CRT
684. 836NO INTERSECTION (WNo., NNo., BNo.)■CRT
685. 837TOOL OFFSET INTERFERENCE ERROR (WNo., NNo., BNo.)■CRT
686. 8383-D OFFSET OPTION NOT FOUND (WNo., NNo., BNo.)■CRT
687. 839ILLEGAL OFFSET No. (WNo., NNo., BNo.)■CRT
688. 840CANNED CYCLE OPTION NOT FOUND (WNo., NNo., BNo.)■CRT
689. 841DESIGNATED TOOL NOT FOUND (WNo., NNo., BNo.)■CRT
690. 842SUB PROGRAM NESTING EXCEEDED (WNo., NNo., BNo.)■CRT
691. 843DESIGNATED SNo. NOT FOUND (WNo., NNo., BNo.)■CRT
692. 844PROGRAM No. NOT FOUND (WNo., NNo., BNo.)■CRT
693. 845ILLEGAL VARIABLE COMMAND (WNo., NNo., BNo.)■CRT
694. 846DESIGNATED NUMBER NOT FOUND (WNo., NNo., BNo.)■CRT
695. 847NO “=” CODE IN PROGRAM (WNo., NNo., BNo.)■CRT
696. 848M98 OPTION NOT FOUND (WNo., NNo., BNo.)▲WRN
697. 849FIGURE ROTATE NESTING EXCEEDED (WNo., NNo., BNo.)▲WRN
698. 850G68 AND M98 COMMANDS SAME BLOCK (WNo., NNo., BNo.)■CRT
699. 851G68 OPTION NOT FOUND (WNo., NNo., BNo.)■CRT
700. 852USER MACRO OPTION NOT FOUND (WNo., NNo., BNo.)■CRT
701. 853EXTERNAL MACRO OPTION NOT FOUND (WNo., NNo., BNo.)■CRT
702. 854INCORRECT USERMACRO PROGRAMMING (WNo., NNo., BNo.)■CRT
703. 855USER MACRO NESTING EXCEEDED (WNo., NNo., BNo.)■CRT
704. 856USER MACRO ARGUMENT EXCEEDED (WNo., NNo., BNo.)■CRT
705. 857INCORRECT USER MACRO G67 PROG. (WNo., NNo., BNo.)■CRT
706. 858USER MACRO “[” NESTING EXCEEDED (WNo., NNo., BNo.)■CRT
707. 859NUMBER OF PARENTHESIS MIS-MATCH (WNo., NNo., BNo.)■CRT
708. 860CALCULATION IMPOSSIBLE (WNo., NNo., BNo.)■CRT
709. 861DIVISION BY ZERO (WNo., NNo., BNo.)■CRT
710. 862INTEGER VALUE OVERFLOW (WNo., NNo., BNo.)■CRT
711. 863REAL VALUE OVERFLOW (WNo., NNo., BNo.)■CRT
712. 864“IF” STATEMENT ERROR (WNo., NNo., BNo.)■CRT
713. 865“WHILE” STATEMENT ERROR (WNo., NNo., BNo.)■CRT
714. 866“SETVN” STATEMENT ERROR (WNo., NNo., BNo.)■CRT
715. 867DO-END NESTING EXCEEDED (WNo., NNo., BNo.)■CRT
716. 868DO-END MIS-MATCH (WNo., NNo., BNo.)■CRT
717. 869NO USER MACRO IN TAPE MODE (WNo., NNo., BNo.)■CRT
718. 870ILLEGAL VARIABLE NAME (WNo., NNo., BNo.)■CRT
719. 871VARIABLE NAME EXISTS (WNo., NNo., BNo.)■CRT
720. 872G51 OPTION NOT FOUND (WNo., NNo., BNo.)■CRT
721. 873G51.1 OPTION NOT FOUND (WNo., NNo., BNo.)■CRT
722. 874CORNER R/C OPTION NOT FOUND (WNo., NNo., BNo.)■CRT
723. 875NOT FOUND GEOMETRIC OPTION (WNo., NNo., BNo.)■CRT
724. 876NOT FOUND GEOMETRIC OPTION (WNo., NNo., BNo.)■CRT
725. 877G15 OPTION NOT FOUND (WNo., NNo., BNo.)■CRT
726. 878ADDRESS CHANGE OPTION NOT FOUND (WNo., NNo., BNo.)■CRT
727. 879G10 OPTION NOT FOUND (WNo., NNo., BNo.)■CRT
728. 880AXIS NOT ZERO RETURNED (WNo., NNo., BNo.)■CRT
729. 881G30 OPTION NOT FOUND (WNo., NNo., BNo.)■CRT
730. 882ILLEGAL COMMAND CROSS MACHINING (WNo., NNo., BNo.)■CRT
731. 883ILLEGAL CROSS MACHINING COMMAND (WNo., NNo., BNo.)■CRT
732. 884REFERENCE POINT RETURN CHECK (WNo., NNo., BNo.)■CRT
733. 885G22 OPTION NOT FOUND (WNo., NNo., BNo.)■CRT
734. 886BEYOND AREA OF G22 (WNo., NNo., BNo.)■CRT
735. 887TAPE I/O ERROR (WNo., NNo., BNo.)■CRT
736. 888FILE I/O ERROR ( , )■CRT
737. 889G37 OPTION NOT FOUND (WNo., NNo., BNo.)■CRT
738. 890G31 OPTION NOT FOUND (WNo., NNo., BNo.)■CRT
739. 891G31.1 - G31.3 OPTION NOT FOUND (WNo., NNo., BNo.)■CRT
740. 892AUTO PROGRAMMING FAILURE (WNo., NNo., BNo.)■CRT
741. 893PROGRAM DATA MISSING ( , )■CRT
742. 894MAZATROL PROGRAM DESIGNATED ( , )■CRT
743. 895—●NTC
744. 896ILLEGAL CHAMFERING ( , )■CRT
745. 897LAP CYCLE BLOCK NUMBER EXCEED ( , )■CRT
746. 898LAP CYCLE ILLEGAL SHAPE DESIGN. ( , )■CRT
747. 899ILLEGAL TAPER LENGTH ( , )■CRT
748. 900—●NTC
749. 901INCORRECT FIXED CYCLE COMMAND (WNo., NNo., BNo.)■CRT
750. 902G10 OPTION NOT FOUND (WNo., NNo., BNo.)■CRT
751. 903ILLEGAL G10 L NUMBER (WNo., NNo., BNo.)■CRT
752. 904ILLEGAL G10 OFFSET No. (WNo., NNo., BNo.)■CRT
753. 905G11 OPTION NOT FOUND (WNo., NNo., BNo.)■CRT
754. 906NO S DIRECTIVE IN FIXED CYCLE (WNo., NNo., BNo.)■CRT
755. 907DIFFERENT SPINDLE TYPE (WNo., NNo., BNo.)■CRT
756. 908NO PITCH IN FIXED CYCLE (WNo., NNo., BNo.)■CRT
757. 909ILLEGAL PITCH IN FIXED CYCLE (WNo., NNo., BNo.)▲WRN
758. 910—●NTC
759. 911CORNER R/C OPTION NOT FOUND (WNo., NNo., BNo.)▲WRN
760. 912NO MOTION COMMAND AFTER R/C (WNo., NNo., BNo.)▲WRN
761. 913INCORRECT R/C COMMAND (WNo., NNo., BNo.)▲WRN
762. 914INCORRECT COMMAND AFTER R/C (WNo., NNo., BNo.)▲WRN
763. 915ANGLE < 1 DEGREE (WNo., NNo., BNo.)▲WRN
764. 916GEOMETRIC COMMAND NOT ABSOLUTE (WNo., NNo., BNo.)▲WRN
765. 917NO LINEAR COMMAND IN 2ND BLOCK (WNo., NNo., BNo.)▲WRN
766. 918INCORRECT ANGLE DATA (WNo., NNo., BNo.)■CRT
767. 919INCORRECT PLANE SELECTION CMD. (WNo., NNo., BNo.)■CRT
768. 920G27, M COMMANDS SAME BLOCK (WNo., NNo., BNo.)■CRT
769. 921G29, M COMMANDS SAME BLOCK (WNo., NNo., BNo.)■CRT
770. 922SKIP SPEED ZERO (WNo., NNo., BNo.)■CRT
771. 923ILLEGAL COMMAND G37 AXIS (WNo., NNo., BNo.)■CRT
772. 924G37, H COMMANDS SAME BLOCK (WNo., NNo., BNo.)■CRT
773. 925H CODE REQUIRED (WNo., NNo., BNo.)■CRT
774. 926ILLEGAL G37 SIGNAL (WNo., NNo., BNo.)■CRT
775. 927SKIP COMMAND IN CORRECTING DIA (WNo., NNo., BNo.)■CRT
776. 928ILLEGAL HEAD DATA No. (WNo., NNo., BNo.)■CRT
777. 929HEAD DATA No. NOT FOUND (WNo., NNo., BNo.)■CRT
778. 930ILLEGAL HEAD TYPE (WNo., NNo., BNo.)■CRT
779. 931NO HEAD DATA (WNo., NNo., BNo.)■CRT
780. 932RETURN R POINT IN CUTTING SIDE (WNo., NNo., BNo.)■CRT
781. 933NO 5FACE CUTTING OPTION (WNo., NNo., BNo.)■CRT
782. 934NO HIGH-SPEED MODE OPTION (WNo., NNo., BNo.)■CRT
783. 935NO PRE-INTERP ACCEL/DECEL OPT. (WNo., NNo., BNo.)■CRT
784. 936OPTION NOT FOUND (Option No., 0, 0)■CRT
785. 937ILLEGAL TOOL DESIGNATED (WNo., NNo., BNo.)■CRT
786. 938PARAMETER ERROR ( , )■CRT
787. 939NO THREAD CUTTING OPTION (WNo., NNo., BNo.)■CRT
788. 940NO INVERSE TIME OPTION (WNo., NNo., BNo.)■CRT
789. 941G93 MODE (WNo., NNo., BNo.)■CRT
790. 942NO 3-D CONVERSION OPTION (WNo., NNo., BNo.)■CRT
791. 943CONVERTING IN 3-D COORDINATES (WNo., NNo., BNo.)■CRT
792. 944WRONG CMD. IN 3-D COORDINATES (WNo., NNo., BNo.)■CRT
793. 945NO HV MACHINING FUNC. OPTION (WNo., NNo., BNo.)■CRT
794. 946NO MAZ. SUB PROGRAM OPTION ( , )■CRT
795. 947NO BLOCK SKIP OPTION ( , )■CRT
796. 948NO G54.1 OPTION ( , )■CRT
797. 949NO G52 IN G54.1 MODE ( , )■CRT
798. 950NO SPLINE CUTTING OPTION ( , )■CRT
799. 951NO CORNER C/R COMMAND IN G0/G33 ( , )■CRT
800. 952NO SYNCHRONIZED TAP OPTION (WNo., NNo., BNo.)■CRT
801. 953TOOL DATA INPUT PROCESS ERROR ( , , )■CRT
802. 954SCREW PITCH ERR ( , , )■CRT
803. 955START AND END POINT NOT AGREE (WNo., NNo., BNo.)■CRT
804. 956RESTART OPERATION NOT ALLOWED (WNo., NNo., BNo.)■CRT
805. 957MANUAL INTERRUPT NOT ALLOWED (WNo., NNo., BNo.)■CRT
806. 958AUTO PECKING IMPOSSIBLE (WNo., NNo., BNo.)■CRT
807. 959WORKPIECE COORDINATE ERROR (WNo., NNo., BNo.)■CRT
808. 960SUPERPOSIT CTRL ILLEGAL COMMAND (WNo., NNo., BNo.)■CRT
809. 961ILLEGAL COMMAND 5X RADIUS COMP. (WNo., NNo., BNo.)■CRT
810. 962CANNOT USE 5X RADIUS COMP. (WNo., NNo., BNo.)■CRT
811. 963TURRET MIRROR IMAGE N/A (WNo., NNo., BNo.)■CRT
812. 964DESIGNATED PNo NOT FOUND (WNo., NNo., BNo.)■CRT
813. 965DESIGNATED PNo NOT FOUND (WNo., NNo., BNo.)●NTC
814. 966NO ORBIT MACHINING OPTION (WNo., NNo., BNo.)■CRT
815. 967ILLEGAL CMD IN ORBIT MACHINING (WNo., NNo., BNo.)■CRT
816. 968CANNOT USE ORBIT MACHINING (WNo., NNo., BNo.)■CRT
817. 969—●NTC
818. 970TOOL TIP CTRL PARAMETER ERROR (WNo., NNo., BNo.)■CRT
819. 971CANNOT USE TOOL TIP PT CONTROL (WNo., NNo., BNo.)■CRT
820. 972ILLEGAL CMD TOOL TIP PT CTRL (WNo., NNo., BNo.)■CRT
821. 973ILLEGAL TOOL AXIS VECTOR (WNo., NNo., BNo.)■CRT
822. 974TOOL TIP PT CTRL FORMAT ERROR (WNo., NNo., BNo.)■CRT
823. 975TOOL TIP PT CTRL N/A (WNo., NNo., BNo.)■CRT
824. 976ILLEGAL COMMAND IN G124 (WNo., NNo., BNo.)■CRT
825. 977CANNOT USE G124/G125 (WNo., NNo., BNo.)■CRT
826. 978G124/G125 PARAMETER ERROR (WNo., NNo., BNo.)■CRT
827. 979MACRO USER ALARM ( , )■CRT
828. 980MACRO USER ALARM 1 ( , )■CRT
829. 981MACRO USER ALARM 2 ( , )■CRT
830. 982MACRO USER ALARM 3 ( , )■CRT
831. 983MACRO USER ALARM 4 ( , )■CRT
832. 984MACRO USER ALARM 5 ( , )■CRT
833. 985MACRO USER ALARM 6 ( , )■CRT
834. 986MACRO USER ALARM 7 ( , )■CRT
835. 987MACRO USER ALARM 8 ( , )■CRT
836. 988MACRO USER ALARM 9 ( , )■CRT
837. 989MACRO USER ALARM 10 ( , )■CRT
838. 990MACRO MEASUREMENT ALARM 1 ( , )■CRT
839. 991MACRO MEASUREMENT ALARM 2 ( , )■CRT
840. 992MACRO MEASUREMENT ALARM 3 ( , )■CRT
841. 993MACRO MEASUREMENT ALARM 4 ( , )■CRT
842. 994MACRO MEASUREMENT ALARM 5 ( , )■CRT
843. 995MACRO MEASUREMENT ALARM 6 ( , )■CRT
844. 996MACRO MEASUREMENT ALARM 7 ( , )■CRT
845. 997MACRO MEASUREMENT ALARM 8 ( , )■CRT
846. 998MACRO MEASUREMENT ALARM 9 ( , )■CRT
847. 999MACRO MEASUREMENT ALARM 10 ( , )■CRT
848. 1001SMART SAFE OPER. SYSTEM ERROR1 (No., Information, )■CRT
849. 1002SMART SAFE OPER. SYSTEM ERROR2 (No., Axis name, )■CRT
850. 1003SMART SAFE OPER. SYSTEM ERROR3 (No., Information, )■CRT
851. 1004SMART SAFE OPER. SYSTEM ERROR4 (No., Information, )■CRT
852. 1005SMART SAFE OPER. SYSTEM ERROR5 (No., Axis name, )■CRT
853. 1006SMART SAFE OPER. SYSTEM ERROR6 (No., )■CRT
854. 1007SMART SAFE OPER. SYSTEM ERROR7■CRT
855. 1020SMART SAFE OPER. SYSTEM ALARM1 (No., Axis name, )■CRT
856. 1021SMART SAFE OPER. SYSTEM ALARM2 (No., Information, )■CRT
857. 1022SMART SAFE OPER. SYSTEM ALARM3 (No., Axis name, )■CRT
858. 1023SMART SAFE OPER. SYSTEM ALARM4 (No., )■CRT
859. 1024SMART SAFE OPER. SYSTEM ALARM5 (No., )■CRT
860. 1101INTERFERE▲WRN
861. 1102INTERFERE■CRT
862. 1103INTERFERE CHECK DATA OVERLOAD●NTC
863. 1104RAPID FEED OVERRIDE SET AT 0▲WRN
864. 1105SAFETY SHIELD CALCULATING●NTC
865. 1106SAFETY SHIELD FAILURE (Cause, Alarm No., )■CRT
866. 1107INCOMPLETE TOOL DATA■CRT
867. 1108CANNOT CHANGE OPERATION MODE●NTC
868. 1109TOOL LENGTH OVER■CRT
869. 1112CANNOT DETACH SPINDLE (Spindle No., )■CRT
870. 1114SIMULTANEOUS AXIS EXCEEDED (WNo., UNo., SNo.)■CRT
871. 1115AXIS NUMBER ERROR (No., )●NTC
872. 1122INTERFERE (WNo., UNo., SNo.)■CRT
873. 1123ILLEGAL OPE (SAFETY SHIELD) (Cause, )■CRT
874. 1124ILLEGAL CYCLE START■CRT
875. 1125SAFETY SHIELD CALCULATING●NTC
876. 1127INVALID SAFETY SHIELD●NTC
877. 1128SAFETY SHIELD CONDITION CHANGED●NTC
878. 1129MEMORY PROTECT (SAFETY SHIELD)●NTC
879. 1130EXCESSIVE SPACE ERROR COMP. (WNo., UNo., SNo.)●NTC
880. 1131NO SPACE ERROR COMP. DATA■CRT
881. 1132ILLEGAL CHOPPING CONDITION (Cause, )■CRT
882. 1133ILLEGAL OPERATION IN CHOPPING (Cause, )●NTC
883. 1134CHOPPING OVERRIDE SET AT 0 (Cause, )▲WRN
884. 1136HOB WORK SPINDLE ROT. EXCEEDED■CRT
885. 1137SAFETY SHIELD CONDITION CHANGED●NTC
886. 1138INVALID SAFETY SHIELD(MATERIAL)●NTC
887. 1139ILLEGAL COMMAND (SAFETY SHIELD)■CRT
888. 1141ILLEGAL OPER CUTTING PT CTRL●NTC
889. 1145ILLEGAL OPER CUTTING PT CTRL (WNo., NNo., BNo.)■CRT
890. 1152CANNOT USE ORBIT MACHINING (Cause, )■CRT
891. 1153ILLEGAL OPER IN ORBIT MACHINING (Cause, )▲WRN
892. 1154FEED LIMITED IN ORBIT MACHINING●NTC
893. 1155G124 MOTION RANGE EXCEEDED (Axis name, )■CRT
894. 1157ILLEGAL OPERATION IN ENGRAVING▲WRN
895. 1158SENSOR ON WITH MOVING MULTI-AX■CRT
896. 1159ILLEGAL WRITING TOOL-OFFSET■CRT
897. 1160SAFETY SHIELD SYNCHRONOUS●NTC
898. 1203DOOR OPEN CONDITION ERROR▲WRN
899. 1204AUTO DOOR CONTROLLER MALF.■CRT
900. 1205AUTOMATIC DOOR SPEED ABNOMALY■CRT
901. 1206AUTO DOOR OVERLOAD■CRT
902. 1207TOOL FITTING ALARM■CRT
903. 1208TOOL FITTING ERR(CUTTING I.L.)▲WRN
904. 1209LINE FILTER ALARM▲WRN
905. 1210LINE FILTER MALFUNCTION●NTC
906. 1217LINE FILTER ALARM(HIGH PRESS)▲WRN
907. 1218LINE FILTER MALF.(HIGH PRESS)●NTC
908. 1219COND.MISSING(CHUCK CLOSE)■CRT
909. 1226COND.MISSING(NOT TURNING MODE)■CRT
910. 1238COND.MISSING(DOOR OPEN)■CRT
911. 1248TOOL EYE MEASURE OFFSET ALARM■CRT
912. 1267B AXIS ROTATION INHL.(SP ROT)●NTC
913. 1268B AXIS ROTATION INHL.(AX POS)●NTC
914. 1269B AXIS ROTATION INHL.(DOOR/CV)●NTC
915. 1282START ERROR (3D MODEL)●NTC
916. 1294TAIL REVERSE INHIBIT●NTC
917. 1296TAIL MCODE ERR (SPINDLE RUN!!)▲WRN
918. 1297THRUST-CONTROL ON●NTC
919. 1319INVALID HANDLE INTERRUPT●NTC
920. 1322COND.MISSING(DOOR OPEN)●NTC
921. 1325COOLANT CHILLER UNIT MALF.▲WRN
922. 1350RECOVERY MODE IMPOSSIBLE.●NTC
923. 1351ATC RECOVERY MODE SELECTED●NTC
924. 1352TOOL No.OK?(SPDL,NEXT, )--->●NTC
925. 1380NEED BEARING MAINTENANCE■CRT
926. 1387MONITORING SENSOR MALF.●NTC
927. 1388TSP EXCEEDED SPEED LIMIT●NTC
928. 1389FREEZE ALARM(COOLANT CHILLER)●NTC
929. 1392SPINDLE CONDITION WARNING■CRT
930. 1400SYSTEM ERROR●NTC
931. 1401FILE OPEN ERROR●NTC
932. 1402FILE READ ERROR●NTC
933. 1403FILE WRITE ERROR●NTC
934. 1404MEMORY PROTECT (DATA IN USE)●NTC
935. 1405FILE SIZE ERROR●NTC
936. 1406LOW MEMORY●NTC
937. 1407FILE CREATION ERROR●NTC
938. 1408DATA TRANSFER ERROR●NTC
939. 1409MILLING ONLY SELECTED●NTC
940. 1410MILL & TURN (WPC) SELECTED●NTC
941. 1411MILL & TRN (Z-OFS) SELECTED●NTC
942. 1412INCORRECT G-CODE●NTC
943. 1413INCORRECT RUNNING MODE●NTC
944. 1414PROGRAM WRITING●NTC
945. 1415ZERO CALCULATED TOOL LENGTH●NTC
946. 1416CANNOT INDEX TOOL●NTC
947. 1417PARAMETER ERROR●NTC
948. 1418CANNOT USE LOWER TURRET●NTC
949. 1420FILE SIZE LIMIT EXCEEDED●NTC
950. 1421DATA ERROR●NTC
951. 1422PROGRAM LAYOUT ERROR●NTC
952. 1423TOOL PATH CHECK NOT COMPLETE●NTC
953. 1424BARRIER INFORMATION NOT SET●NTC
954. 1425ILLEGAL SETUP DATA●NTC
955. 1426NO PROG LAYOUT FOR THIS PROCESS●NTC
956. 14273D INTERFRNCE CHECK MODEL ERROR●NTC
957. 1428INCORRECT POCKET FOR LBB●NTC
958. 1429CANNOT PERFORM AUTO SET●NTC
959. 1430NOT ACTIVE PROGRAM●NTC
960. 1431AUTO SET ERROR●NTC
961. 1432TOOLMODEL NOT SELECTED●NTC
962. 1433SAME TOOL MODEL NAME IN USE●NTC
963. 1434INCOR CRS POS FOR PROG LAYOUT●NTC
964. 14353D MONITOR MANUAL MODE ONLY●NTC
965. 1436DIFFERENT TYPE OF PROGRAM●NTC
966. 1437CANNOT TRANSFER ACTIVE PROGRAM●NTC
967. 1438NO SETUP DATA●NTC
968. 1439CANNOT CHANGE UNIT●NTC
969. 1440ID No. NOT FOUND●NTC
970. 1441FILE NOT FOUND●NTC
971. 1442ILLEGAL TOOL- CANNOT ASSIGN●NTC
972. 1443BACKUP INCOMPLETE●NTC
973. 1444PROCESS TOO LARGE -DEVIDE PROC●NTC
974. 1445SAME SIMULTAN. NO IN RGH & FIN●NTC
975. 1446CANNOT CHNG WNo (SNGL PROC MODE)●NTC
976. 1447RESTORE OPERATION STOPPED●NTC
977. 1448TOOL LENGTH OVER●NTC
978. 1449NC PROGRAM MEMORY SIZE OVER (AREA, )●NTC
979. 1450SELECT LOWER TURRET●NTC
980. 1451TILT TABLE ANGLE INCORRECT●NTC
981. 1452SPINDLE CONDITION CAUTION●NTC
982. 1453MEMORY PROTECT (BACK UP)●NTC
983. 1454MEMORY PROTECT (RESTORE)●NTC
984. 1455ILLEGAL MAKER NAME●NTC
985. 1456ILLEGAL MODEL NO.●NTC
986. 1457CANNOT EDIT MAKER MADE DATA●NTC
987. 1458NO DESIGNATED PROGRAM●NTC
988. 1460CANNOT USE V.M. DURING AUTO OPE●NTC
989. 1461TOOL MODEL IMPORT FAILURE●NTC
990. 1462CANNOT USE DISPLAY SAVE DATA●NTC
991. 1463INVALID HANDLE INTERRUPT●NTC
992. 1464DEVICE ERROR●NTC
993. 1466ILLEGAL ATTACHMENT No.●NTC
994. 1467SETTING RANGE EXCEEDED●NTC
995. 1470INCORRECT DESIGNATED DATA (Note)●NTC
996. 14711BLOCK SIZE OVER●NTC
997. 1472INVALID REEDIT●NTC
998. 1473NOT AUTO MODE●NTC
999. 1474MEASURED RESULT MALFUNCTION●NTC
1000. 1475ILLEGAL MEASURING CONDITION●NTC
1001. 1477INCORRECT PROCESS SELECTION●NTC
1002. 1482CANNOT LOCK (LIMIT NUMBER)●NTC
1003. 1485DATA GUARD ALARM (No., )●NTC
1004. 1486ILLEGAL ID OR PASSWORD (No., )●NTC
1005. 1487ID NOT SELECT (No., )●NTC
1006. 1488PASSWORD MISMATCH (No., )●NTC
1007. 1489ILLEGAL CHARACTER (No., )●NTC
1008. 1490SAME ID ALREADY EXISTS (No., )●NTC
1009. 1491RANK NOT SELECT (No., )●NTC
1010. 1492ACCOUNT NUMBER OVER (No., )●NTC
1011. 1493ILLEGAL –9999 CODE (No., )●NTC
1012. 1494CANNOT EDIT SMC DATA (No., )●NTC
1013. 1495SMC DATA NOT SETUP (No., )●NTC
1014. 1496ILLEGAL ITS PARAMETER●NTC
1015. 1601ILLEGAL ATC MODE (WNo., UNo., SNo.)■CRT
1016. 1602SET INDEX UNIT BEFORE MACHINING (WNo., UNo., SNo.)■CRT
1017. 1603PROGRAM IS NOT WPC. (WNo., UNo., SNo.)■CRT
1018. 1604ILLEGAL TOOL DIRECTION (INDEX B) (WNo., UNo., SNo.)■CRT
1019. 1605LOW TUR CANNOT EXECUTE MIRROR (WNo., UNo., SNo.)■CRT
1020. 1606ILLEGAL CUTTING ANGLE (WNo., UNo., SNo.)■CRT
1021. 1607NEED TOOL ROTATION DIRECTION ( )■CRT
1022. 1608NEED SELECT TABLE UNIT (WNo., UNo., SNo.)■CRT
1023. 1609CANNOT SET WPC IN 2WORKPIECE (WNo., UNo., SNo.)■CRT
1024. 1610SET INDEX UNIT IN 2WORKPIECE (WNo., UNo., SNo.)■CRT
1025. 1611SET INDEX UNIT AFTER 2WORKPIECE (WNo., UNo., SNo.)■CRT
1026. 1612SET HEAD UNIT AFTER 2WORKPIECE (WNo., UNo., SNo.)■CRT
1027. 1613SET HEAD UNIT IN 2WORKPIECE (WNo., UNo., SNo.)■CRT
1028. 1614NO TABLE ROTATION AXIS (WNo., UNo., SNo.)■CRT
1029. 1615TABLE ROTATION CENTER NOT AGREE (WNo., UNo., SNo.)■CRT
1030. 1616CYLINDER CHAMFERING N/A (WNo., UNo., SNo.)■CRT
1031. 1617CYLINDER CHAMFERING IMPOSSIBLE (WNo., UNo., SNo.)■CRT
1032. 1618—●NTC
1033. 1619ILLEGAL APPROACH SCHEME (WNo., UNo., SNo.)■CRT
1034. 1620—●NTC
1035. 1621NO INDEX UNIT AFTER 5 FACE (WNo., UNo., SNo.)■CRT
1036. 1622NO WPC UNIT AFTER 5 FACE (WNo., UNo., SNo.)■CRT
1037. 1623TPC RELAY POINT SET IN 5 FACE (WNo., UNo., SNo.)■CRT
1038. 1624ILLEGAL UNIT IN 5 FACE (WNo., UNo., SNo.)■CRT
1039. 1625ATTACHMENT NO. MISMATCH (WNo., UNo., SNo.)■CRT
1040. 1626ILLEGAL COMMAND (ATTACHMENT) (WNo., UNo., SNo.)■CRT
1041. 1700LAYOUT UNABLE ( , )■CRT
1042. 1705AVOIDANCE DISTANCE EXCEEDED (WNo., UNo., SNo.)■CRT
1043. 1706UNCUT EXIST (WNo., UNo., SNo.)●NTC
1044. 1707UNCUT INCREASING (WNo., UNo., SNo.)●NTC
1045. 1708IPM PATH IMPOSSIBLE (WNo., UNo., SNo.)■CRT
1046. 1709ILLEGAL CUTTING FACE (C-AXIS) (WNo., UNo., SNo.)■CRT
1047. 1800CANNOT CHANGE TIME CONSTANT (WNo., NNo., BNo.)■CRT
1048. 1801ILLEGAL COMMD TIME CONST. CHANGE (WNo., NNo., BNo.)■CRT
1049. 1802ILLEGAL STARTUP CONDITION G12.1 (WNo., NNo., BNo.)■CRT
1050. 1803ILL GCODE (2ND SPDL POS ONLY) (WNo., NNo., BNo.)■CRT
1051. 1804NO Z-OFFSET (WNo., NNo., BNo.)■CRT
1052. 1805G68.2 OPTION NOT FOUND (WNo., NNo., BNo.)■CRT
1053. 1806ILLEGAL CMD TILTED PLANE CMD (WNo., NNo., BNo.)■CRT
1054. 1807CANNOT USE G68.2 (WNo., NNo., BNo.)■CRT
1055. 1808CANNOT USE G53.1 (WNo., NNo., BNo.)■CRT
1056. 1809TILTED PLANE CMD FORMAT ERROR (WNo., NNo., BNo.)●NTC
1057. 1810TILTED PLANE CANNOT BE DEFINED (WNo., NNo., BNo.)●NTC
1058. 1811CANNOT USE G43.1 (WNo., NNo., BNo.)■CRT
1059. 1812ILLEGAL CMD IN G43.1 MODE (WNo., NNo., BNo.)■CRT
1060. 1813G54.4 OPTION NOT FOUND (WNo., NNo., BNo.)■CRT
1061. 1814ILLEGAL CMD IN G54.4 MODE (WNo., NNo., BNo.)■CRT
1062. 1815CANNOT USE G54.4 (WNo., NNo., BNo.)■CRT
1063. 1816CANNOT USE G18.1/G18.2/G18.3 (WNo., NNo., BNo.)■CRT
1064. 1817ILLEGAL CMD IN G18.2/G18.3 (WNo., NNo., BNo.)■CRT
1065. 1818ILLEGAL COMMAND (SAFETY SHIELD) ( , )■CRT
1066. 1819ILLEGAL C/S (SAFETY SHIELD) ( , )■CRT
1067. 1820ILLEGAL COMMD IN G54.4 (WNo., NNo., BNo.)■CRT
1068. 1821UNWRITABLE SYSTEM VARIABLE (WNo., NNo., BNo.)■CRT
1069. 1822—●NTC
1070. 1823NOT POSSIBLE SETTING ERROR (WNo., NNo., BNo.)■CRT
1071. 1824UNWRITABLE SYSTEM VARIABLE(ISS) (WNo., NNo., BNo.)■CRT
1072. 1825ILLEGAL M CODE ( , )■CRT
1073. 1826HEAD-AXIS ILLEGAL COMMAND (WNo., NNo., BNo.)■CRT
1074. 1827HEAD-AXIS ANGLE INCORRECT (WNo., NNo., BNo.)■CRT
1075. 1828—●NTC
1076. 1829NO 5 AXIS SPLINE CUTTING OPTION ( , )■CRT
1077. 1830CANNOT USE 5AXIS SPLINE CUTTING (WNo., NNo., BNo.)■CRT
1078. 1831ILLEGAL CHOPPING CONDITION (WNo., NNo., BNo.)■CRT
1079. 1832ILLEGAL COMMAND IN CHOPPING (WNo., NNo., BNo.)■CRT
1080. 1833ILLEGAL COND. CORRECT LENGTH.C (WNo., NNo., BNo.)■CRT
1081. 1834CORRECTING LENGTH.C (WNo., NNo., BNo.)■CRT
1082. 1835FILE ACCESS ERROR (Cause, )■CRT
1083. 1836CANNOT USE CUTTING PT CTRL (WNo., NNo., BNo.)■CRT
1084. 1837ILLEGAL CMD CUTTING PT CTRL (WNo., NNo., BNo.)■CRT
1085. 1838CUTTING PT CTRL FORMAT ERROR (WNo., NNo., BNo.)■CRT
1086. 1839CUTTING PT CONTROL N/A (WNo., NNo., BNo.)■CRT
1087. 1845CORNER SMOOTH CONTROL N/A (WNo., NNo., BNo.)■CRT
1088. 1846VARIABLE ACCELERATION CTRL N/A (WNo., NNo., BNo.)■CRT
1089. 19002 CHARACTER AXIS ILLEGAL FORMAT (WNo., NNo., BNo.)■CRT
1090. 1901ILLEGAL ABSOLUTE AXIS NAME (WNo., NNo., BNo.)■CRT
1091. 1902ILLEGAL INCREMENT AXIS NAME (WNo., NNo., BNo.)■CRT
1092. 1903NO INVOLUTE OPTION (WNo., NNo., BNo.)■CRT
1093. 1904ILLEGAL CMD DURING G2.2/G3.2 (WNo., NNo., BNo.)■CRT
1094. 1905THIS MODE CANNOT CMD G2.2/G3.2 (WNo., NNo., BNo.)■CRT
1095. 1906G2.2/G3.2 FORMAT ERROR (WNo., NNo., BNo.)■CRT
1096. 19075AXIS PARAM SELECT N/A (WNo., NNo., BNo.)■CRT
1097. 1908CANNOT USE 5AXIS PARAM SELECT (WNo., NNo., BNo.)■CRT
1098. 1909SAFETY SHIELD SYNC FAILURE ( , , )■CRT
1099. 1910—●NTC
1100. 1911ENGRAVING N/A (WNo., NNo., BNo.)■CRT
1101. 1912CANNOT USE ENGRAVING (WNo., NNo., BNo.)■CRT
1102. 1913ILLEGAL ARC RADIUS OF ENGRAVING (WNo., NNo., BNo.)■CRT
1103. 1914TEXT HEIGHT INVALID OF ENGRAV. (WNo., NNo., BNo.)■CRT
1104. 1915POS ADJUST OF G124 INCOMPLETE (WNo., NNo., BNo.)■CRT
1105. 1916HOB AXIS PARAMETER ERROR ( , )■CRT
1106. 1991NOT POSSIBLE CROSS MACHINING (WNo., NNo., Cause)■CRT
1107. 1992ILLEGAL AXES QTY. FOR CROSS (WNo., NNo., BNo.)■CRT
1108. 2001CAD FILE FORMAT ERROR ( , )●NTC
1109. 2028ILLEGAL WORKPIECE DIMENSION ( , )●NTC
1110. 2029ILLEGAL FIXTURE DIMENSION ( , )●NTC
1111. 2030CANNOT REGISTER (NUMBERS FULL) ( , )●NTC
1112. 2031SELECT REGISTERED DATA ( , )●NTC
1113. 2032SELECT DATA TO CHANGE ( , )●NTC
1114. 2033SELECT DATA TO DELETE ( , )●NTC
1115. 2034CANNOT ADD WORKPCE MATERIAL ( , )●NTC
1116. 2035CANNOT ADD FIXTURE ( , )●NTC
1117. 2036SURFACE SELECTION ERROR ( , )●NTC
1118. 2037DATA NOT REGISTERED ( , )●NTC
1119. 2038FILE WITH SAME NAME EXISTS ( , )●NTC
1120. 2039FILE NAME TOO LONG ( , )●NTC
1121. 2040WRITING ERROR ( , )●NTC
1122. 2049NUMBER OF JAWS = 0 ( , )●NTC
1123. 2051MODEL SELECTION ERROR ( , )●NTC
1124. 2052MODEL SELECTION ERROR ( , )●NTC
1125. 2053ILLEGAL SURFACE TYPE ( , )●NTC
1126. 2054ILLEGAL SURFACE ORIENTATION ( , )●NTC
1127. 2055NO PARALLEL PLANE ( , )●NTC
1128. 2056ILLEGAL FILE NAME ( , )●NTC
1129. 2057NUMBER ALREADY REGISTERED ( , )●NTC
1130. 2061WORK MATL LARGER THAN BARRIER ( , )●NTC
1131. 2062FIXTURE LARGER THAN BARRIER ( , )●NTC
1132. 2063CANNOT MOVE MODEL ( , )●NTC
1133. 2064— ( , )●NTC
1134. 2065NO 2ND SPINDLE ( , )●NTC
1135. 2066CANNOT CHANGE MATERIAL ORDER ( , )●NTC
1136. 2067ILLEGAL BOOLEAN OPERATION ( , )●NTC
1137. 2074CANNOT CHANGE TABLE AXIS ( , )●NTC
1138. 2075SETUP DATA DO NOT MATCH ( , )●NTC
1139. 2076CANNOT SELECT FEATURE POINT ( , )●NTC
1140. 2077SELECT SET FEATURE POINT ( , )●NTC
1141. 2078CANNOT ADD BASE POINT ( , )●NTC
1142. 2079ILLEGAL GRID VIEW SETTING ( , )●NTC
1143. 2080ILLEGAL WORK OFFSET SETTING ( , )●NTC
1144. 2084CANNOT CHANGE ASSEMBLE ( , )●NTC
1145. 2085CANNOT SELECT PLANE ( , )●NTC
1146. 2086SELECT ROTATE AXIS ( , )●NTC
1147. 2087CANNOT CONVERT WORKPCE ( , )●NTC
1148. 2088WORKPCE CONVERTING ( , )●NTC
1149. 2100MACN INTRF (WNo., UNo., SNo.)●NTC
1150. 2101NEAR MISS (WNo., UNo., SNo.)●NTC
1151. 2102WORK INTRF (WNo., UNo., SNo.)●NTC
1152. 2110ILLEGAL FORMAT ( , )●NTC
1153. 2111NO SOLID CHECK IN AUTO OPER ( , )●NTC
1154. 2112Z-OFFSET NOT FOUND (WNo., , )●NTC
1155. 2113JAW NO NOT FOUND (WNo., , )●NTC
1156. 2120RESTART PT SEARCH INTERRUPTED ( , )●NTC
1157. 2121RESTART POINT NOT FOUND ( , )●NTC
1158. 2130CANNOT CHECK WORKPIECE MODEL ( , )●NTC
1159. 2140CANNOT DISPLAY MACHINE MODEL ( , )●NTC
1160. 2150CANNOT DISPLAY TOOL MODEL ( , )●NTC
1161. 2151CANNOT DISPLAY T/S CENTER ( , )●NTC
1162. 2160ILLEGAL CYCLE START ( , )▲WRN
1163. 2190NO MACHINE MODEL ( , )●NTC
1164. 2191CANNOT SELECT CHECK UNITS ( , )●NTC
1165. 2192CHECK UNITS SET ERROR ( , )●NTC
1166. 2193— ( , )●NTC
1167. 2194CONVERTED WORKPCE DO NOT EXIST ( , )●NTC
1168. 2195NEED CONVERT WORKPCE AGAIN ( , , )●NTC
1169. 2201READ-ONLY MEDIA ( , )●NTC
1170. 2202NETWORK LOGON FAILED ( , )●NTC
1171. 2203NETWORK PATH NOT FOUND ( , )●NTC
1172. 2204HARDWARE NOT INSTALLED ( , )●NTC
1173. 2205CANNOT ACCESS FILE ( , )●NTC
1174. 2206FILE CONFIGURATION ERROR ( , )●NTC
1175. 2207CANNOT ACCESS CNC ( , )●NTC
1176. 2208MACHINE DATA TRANSFER ERROR ( , )●NTC
1177. 2209CANNOT SAVE MACHINE DATA (Note, )●NTC
1178. 2210INVALID DRIVE SPECIFIED ( , )●NTC
1179. 2211FILE SAVINGFAILURE ( , )●NTC
1180. 2212FILE NOT FOUND ( , )●NTC
1181. 2600— ( , )●NTC
1182. 2604TAP SIZE OVER ( , )●NTC
1183. 2605— ( , )●NTC
1184. 2606LICENSE IMPORT ERROR (No., Type, )●NTC
1185. 2607— ( , )●NTC
1186. 2608— ( , )●NTC
1187. 2609MEMORY PROTECT (TRIAL MODE) ( , )●NTC
1188. 2610TOOL DATA MEASURING ( , )●NTC
1189. 2611TOOL OFFSET MEASURING●NTC
1190. 2612DESIGNATED TOOL NOT FOUND (WNo., UNo., SNo.)●NTC
1191. 2613ILLEGAL PROGRAM AREA●NTC
1192. 2614PROGRAM STOP WHILE WAITING (Head No., , , )●NTC
1193. 2615PROJECT NOT FOUND●NTC
1194. 2616MAX NUMBER OF PROJECTS EXCEEDED●NTC
1195. 2617SAME PROJECT EXISTS●NTC
1196. 2618CANNOT DISPLAY CROSS SECTION●NTC
1197. 2619ANALYZED DATA SIZE EXCEEDED●NTC